Jump to content
SAU Community

Recommended Posts

hey guys been wanting to do this run for a while so its happening on the 3/6/12

everyone welcome (imports and cool cars only)

we will be meeting at the carpark at kariong on the corner of the avenue and festival drive just off the central coast hwy

meeting time: 10am

leaving time: 10:45am (sharp)

this is a non offical sau event but lets behave and have sum fun its a great road so lets get home in one piece.

destination: carpark at berowra near rsl club.

the rsl has great food so hopefully get there about lunch time for a feed

there is a shell servo across the road from the meeting point so fuel up before you get to the meeting point please.

happy to answer any questions you guys and girls have but let me know if your in

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

Just a tip, 3/6 is a Sunday, old pac at that time of day will be inundated with motorbikes of all sorts and tourists...

Though if Im around I'll turn up... I like checking out other skylines and cool cars...

I am assuming my car will be all tuned and ready by the end of May so will probably join this as long as there arent too many tools that are likely to attract the boys in blue?

late night drives always find old pac clear and with the window down all you hear is sound of RB echoing thru the valley...

Agreed, I think saturday night is a good option.

as long as there arent too many tools that are likely to attract the boys in blue?

Hopefully if we only advertise this on SAU and keep it at a smaller number of people than usual we shouldn't get any idiots

we will be meeting at the carpark at kariong on the corner of the avenue and festival drive just off the central coast hwy

Is this the kariong info centre carpark man?

Anyway I'm pretty keen for the cruise so ill see everyone there

Agreed, I think saturday night is a good option.

Hopefully if we only advertise this on SAU and keep it at a smaller number of people than usual we shouldn't get any idiots

Is this the kariong info centre carpark man?

Anyway I'm pretty keen for the cruise so ill see everyone there

yeh mate thats where it is,we will make it the saturday night meet at 5pm leave at 5:45pm sharp

2/6/12 at night?

In for this, never done old PAC

yes guys this will be held on the 2/6/12 meeting at 5pm and leaving at 5:45pm.everything else will remain the same but have changed to a night run to avoid excess traffic.we should arive at berowra rsl about 7:30 ish for dinner.not sure how to edit first post so changed it here

Hey Anthony,

If i do go on this one we should organise a mini cruise from up this way to the meet up point in Kariong ;)

Hey mate, was almost going to mention this, sounds good, will have a think about a good spot and post something closer to the date, good luck with getting your car sorted!




  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...