Jump to content
SAU Community

Recommended Posts

Hey guys, have been searching the forums to no avail for someone who has had similar problems that I am having with my r33 Gtr.

First gear is really hard to engage, same with reverse. And a little notchy throught all of the gears. Mostly like this all the time, I think temperature has a bit to do with it as well as when cold, still notchy and hard to engage but not as bad as when it's hot.

If I roll slowly (-5km/h) it pops into 1st no problems.

Master cylinder is full, visually everything seems to be ok. No leaks that I can see out of the slave cylinder.

Clutch started slipping a tiny bit in 3rd the other morning (gearbox still cool), could this all be tied in?

Really confused and need to get this fixed quickly, its my daily at the moment.

Anyone have any ideas?

Thanks guys.

No clue, I purchased the car a few months ago. Reason I haven't changed it is that I am doing the 100k service next month so I was going to get it all taken care of in 1 hit. This happened all of a sudden though, so I'm guessing it's not that. It was smooth a few days ago and now it's a bitch to drive.

Clutches don't slip if in good condition and nothing wrong, shouldn't matter if its cold or not ( unless its a full carbon, but thats another story ) :closedeyes:

Load it up in 4th and see if it slips again, could answer your question. also change fluid ( make sure you use the right weight oil )

Car is 15+ years old, could just be normal wear on box..

Edited by tricstar

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Yea... this is what i thought too. Ill check this out aswell.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
    • Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
×
×
  • Create New...