Jump to content
SAU Community

Recommended Posts

Yeh, it could well have been my fault. Kick in the teeth considering how careful I was installing it, I was paranoid about even scratching anything. In any case, I guess it's irrelevant who caused it. It's happened now, better just get on with what I'm gonna do about it. Unfortunately I may be a little bit out of my depth now.

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Alright guys, I just need to make it clear to anyone who has read/is reading this thread that I can't and don't blame the workshop for what has happened. I was upset yesterday about the situation with my car, and I've run my mouth off a bit in regards to it being their fault. That really wasn't the right thing to do, as this could all have quite easily been my fault, and I accept that and will just get on with fixing it.

Allstar have been nothing but helpful while I've had my car in there, and in fact continue to be helpful despite my comments on here. I guess a little bit of miscommunication between them and me about what exactly happened with the manifold lead to me jumping to conclusions, and voicing those conclusions on here wasn't the right thing to do. I have since spoken to them and they explained exactly what happened and what they did, and it's quite clear now that I am at fault and I apologize to them for what was said.

Edited by Hanaldo

dont you hate it when workshops pull you up on what gets said online in public space in the free world...

I just wish I still had the lower section sitting in my garage that I could send over to you...

I just wish I still had the lower section sitting in my garage that I could send over to you...

The lower manifold isn't an issue anymore, Allstar supplied a new one and replaced it. It's whatever has got or is getting into the motor jamming my valves open that is the problem.

oh, well in that case I wish I had another head to give you...

That one I would appreciate :P

Do they have you at knifepoint, should we send the police ...:P

So how did it break? or are you gunna be all suspenseful again..

I think I've got the knife at my own throat :/ lol. No but seriously. I did jump to conclusions.

Still not clear what caused the manifold to break though, probably incorrect tightening as you said. I fcked up with that bolt at the front by not drilling the hole out, so that has probably twisted the manifold.

Just out of curiosity, how do you tell compression is down on one cylinder under load?

Well it loses compression under full load, it doesn't pick back up straight away when it returns to idle or is switched off, which is when my tuner did the comp test. But after being switched off for awhile, it will get full compression back and is good to go again.

Well it loses compression under full load, it doesn't pick back up straight away when it returns to idle or is switched off, which is when my tuner did the comp test. But after being switched off for awhile, it will get full compression back and is good to go again.

Which cylinder/s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...