Jump to content
SAU Community

Recommended Posts

I am very keen on the 6boost, please pm me to let me know what you would sell it for alone :) if you will that is

  • 1 month later...

Alcon Mono6 calipers with R35 hats and used PMU rotors ; 380 x 34mm $3500 firm No caliper mounts or lines.. If you want those then I will need to machine them up and cost will be $4200 for a complete bolt on kit with DS2500 pads

Genuine Trust TD06H-25G turbo $1500 firm

Koyo R32 GTR replacement radiator $250ono

R32 GTR headlights $200 ono. The chrome is hazed and peeling.

AU Falcon electric thermo fans $80

  • 3 months later...
  • 2 weeks later...

Had a quick look through the thread. Couldn't see any SOLD replies about the shiftlight and launch control. Still available?

  • 5 months later...

keen on the 32gtr headlights.. read all 5 pages and didn't see that u'd sold them?? PM price plus postage to "5050 SA"

  • 2 weeks later...
  • 8 months later...

Back up for sale is sale my TD05H-18G with 3" inlet. Its a Kando, new and never used. Friend is selling his S13 project car so bits he had called dibs on are being returned.

It has a Subaru core so is 360deg bearing with water cooled core and oil lube

TD05H-18G

med_gallery_462_50_66814.jpg
med_gallery_462_50_185153.jpg
med_gallery_462_50_208537.jpg
med_gallery_462_50_247453.jpg?t=36239728
med_gallery_462_50_22264.jpg


med_gallery_462_50_112743.jpg

med_gallery_462_50_153163.jpg

Asking $540 for the turbo with no exhaust housing or $750 with the Trust 8cm rear housing (3 bolt)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...