Jump to content
SAU Community

Recommended Posts

Hi everyone,

First post from a long time reader!

I'm currently in Japan, and will be for another 10 months or so. It has been a dream of mine to purchase an R32 GT-R for many years now. My master plan is to purchase one here, drive it within Japan for the next 10 months, and then import it back to Australia (for everyday use) when I head back.

Stuff I have worked out so far:

Can't import R32 GT-Rs made between July 1991 and May 1992.

Post May 1992 models would be preferable due to already having side-intrusion bars fitted.

The main thing I am not sure about is to what extent the car must be returned to factory condition upon importing it into Australia. For example, the majority of R32 GT-Rs in Japan seem to have basic modifications such as aftermarket wheels, exhausts, suspension, steering wheels, 320km/h gauge clusters etc., unless I pay the premium for a completely stock one.

Taking into account that I would like to register the car with normal road registration, can anyone please tell me to what extent the car I import needs to be in factory condition?

Thanks heaps :)

Link to comment
https://www.sau.com.au/forums/topic/400545-purchasing-from-within-japan/
Share on other sites

The main thing I am not sure about is to what extent the car must be returned to factory condition upon importing it into Australia. For example, the majority of R32 GT-Rs in Japan seem to have basic modifications such as aftermarket wheels, exhausts, suspension, steering wheels, 320km/h gauge clusters etc., unless I pay the premium for a completely stock one.

Hello, Nice to meet you and good luck with your search.

Are there many stock R32 GTR's left over there? It was very hard for me to find a completely stock R34 GTR and I wanted a particular colour and spec. And the clean close to stock ones over there cost just as much as they did over here in Aus (and thats before you even got them on to the boat + compliance - etc).

There are many which are around 95% stock, with only an aftermarket exhaust for example, but the completely stock ones are few and far between. They are at least double the price of one with a pile of mods, seemingly regardless of mileage. I'm not really too fussed on the one I buy being 100% stock, I just don't want to run into trouble when the time comes to have it complied.

Unfortunately I can't seem to find any definitive information on what is allowed and what isn't. I've read that compliance places often say the brake pads need replacing for example, and that you have to replace them with original Nissan pads. Stuff like this is really turning me off the whole procedure, if only I knew what parts have to be stock, I would be much better off. I might try contacting an importer about it.

Someone like Kristian/Iron Chef will give you a more accurate answer but I believe you must own the car for a minimum 12 months before you can privately import the car (which is easier/cheaper then importing as per usual). Obviously the good thing about doing it this way is that you are not constrained by what is and isn't "eligible for import".

Just something to think about.

Thanks for the advice everyone!

I have one more question about the necessary side-intrusion bars if you don't mind :)

If I purchase an 89/90/91 model over here, and then swap the doors with those from a later model while I am over here, would it be ok? I'm just assuming it would be much easier/cheaper to buy second hand doors here, rather than paying a compliance shop to find and fit them in the Australia.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...