Jump to content
SAU Community

Recommended Posts

most coilovers for stagea are just gtr ones with s14 rear top plates and they dont work PROPERLY. i wouldnt suggest stock gtr shocks either as there is alot of difference between a coupe and a wagon. chase up KYB with the part number stamped on the shocks. if that doesnt work you may have to get a set of stockers refurbished. id suggest teins or genuine nismo stuff as its the only shocks made to suit stagea.

What's the problem with the function of the majority of coilovers Ray?

called KYB aus distributor today, straight up NO on anything JDM. Im thinking ill just leave it for now and figure something out another day when i have some spare cash or when something pops up cheap. genuines were quoted at $190ea front, $330ea rears and that's trade!

You need to go to a better distributor, i got genuine KYB replacement shocks for an r33 off the shelf from a distributor in brisbane. I would guess they could get stagea ones if u have the part no. off them. If ur interested i'll look for the name.

Edited by Raysboostin

What's the problem with the function of the majority of coilovers Ray?

Not so much function, as the setup doesnt suit the application. Out of the ones ive tried the rears are just never right. Ive spent alot of time and money changing springs and making adjustments which amounted to very little. The valving of the shocks on a wagon are not the same as a coupe, so the gtr rears dont really work. But its really relative to use. If u never carry anything in the back or go to the track u prob wont notice the inbalance. Your better off spending the money on a set ofcoilovers designed for a stagea. Rather than a cheap generic set adapted to bolt into anything.

You need to go to a better distributor, i got genuine KYB replacement shocks for an r33 off the shelf from a distributor in brisbane. I would guess they could get stagea ones if u have the part no. off them. If ur interested i'll look for the name.

thanks, i found some Tein struts pretty cheap, if fulcrum ever get back to me, they'll be heading there for servicing then in they go

  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...