Jump to content
SAU Community

Recommended Posts

You pair have nothing

You want a long cruise head out through cessnock to broke then take Charlie's road across to putty rd the head out the golden hwy to sandy hollow and turn onto Bylong Valkey way which goes back to Richmond then a short hop to Windsor and back up putty road to singleton and home

that doesnt look too bad, but looks to actually be a shorter route!

The Putty run we did a few years back was a long day, we did Old Pac, Galston Gorge, Windsor and then Putty Rd through to Singleton..... It was a 2 fuel stop trip on that run..... On that note, how far is that drive in KM? And have you mapped out fuel stops? (Taking into account that ill only make <300kms to a tank lol

ful trip is 650kms... you would have to see where to get your fuel from.

I will bring a spare bottom end, ill have to change that out when u guys fix what u break :ph34r:

Good plan! Anyone got a 2 poster they can bring?

that doesnt look too bad, but looks to actually be a shorter route!

ful trip is 650kms... you would have to see where to get your fuel from.

I fuelled up in Sydney and then again in Singleton on our run.....

But my flex fuel is back on now so i can run whatever, not an issue :) Just have to run low boost with normal pump fuel :( Only 19psi lol

may need to plan this one for winter so its easier on the cars haha..

Yeah plus cooler = more wasps! And if the car bursts into flames we can all sit around the campfire and inhale the E85 goodness!

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Is the head still good?

If its a DE as you say then any VL bottom end with a light hone, new rings and bearings and your head fitted should do nicely

You need to fit an idler pulley for the belt return and I think that's it

Best bet is to do a search on here as there is a heap of info around just have to find it

As far as legalities go I'm not sure but if original engine number then no capacity increase

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Face palm :no:

f**k that sucks man. wonder how much it'll cost to how much you could sell it for.

N/A engines should be cheap and pretty easy to get ahold of man!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...