Jump to content
SAU Community

Recommended Posts

  • Replies 134
  • Created
  • Last Reply

Top Posters In This Topic

Cheers, Kat :) Sumanator, 31 + AE86 looked the goods!

Thanks mate, was good seeing the S13 there, its the old HPI drag project car yeah?

100% Move the barriers in around/behind the start line and re tar would make a massive improvement.

Was good to finally see it in person after reading about it so much back in the day, luckily it still looks much the same from the outside so its pretty easy to recognise!

Now thats commitment ^

Along with moving the barriers in 100m I'll be back next year.

Maybe as an entrant

100% Move the barriers in around/behind the start line and re tar would make a massive improvement.

Barriers will be moved to edge of the big ditch near the runway, Which is 60-70m back from the course, much closer than this years 150m. Won't be going behind start line.

  • 2 months later...

We have been smashed by entry pack request emails (for when they are release in April), with more emails than the 200 spots available for this year. If you are even considering entering, please email [email protected] so you get an entry pack. Nearly all of our 2012 entrants are comin' back as well.

  • 1 month later...
Just a reminder.... If you are looking to enter the 2013 event, you NEED to email [email protected] as Entrant packs are being emailed in 23 days (25/3). We have 200 spots available over 2 days, and we will already be sending out significantly more entrant packs than spots available


I will put a new thread up shortly with new details for this years event

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...