Jump to content
SAU Community

Recommended Posts

Hey guys, I know this is a done topic but im searching for an answer from people who have done this, anyway, I'm in WA with an r32gtr, took it over the pits and have to get it engineered, which means a 5 gas test.

I went over with cams and failed hard, so am going back to stock for for the test and some id1000 injectors and tune to suit.

Where I am struggling for a definitive answer is on on the Cat converter, I 've been reading and am unsure, people are saying stock ceramic cat, so are a couple of shops but 2 other shops have said to go something like a 400 cell euro 4 cat.

I don't know much about this so can anyone that has passed with a similar setup share their experience with what cat would be better or if there are any better ones to go for that would be much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/403635-5-gas-test-and-cat-converter/
Share on other sites

Depends on the tune, too rich will fail, too lean will fail.

I do happen to know what will make you pass. I did IM240 test here in NSW, presume similar test.

I got the cat out of a new bf xr6 turbo, and made it fit my system. its 3" in and outlet.

It was literally running euro 4 standard at most points of the test.

A normal cat will not flow real well compared the the massive substrate in the falcon cat, in which it has enough time in the substrate to properly convert.

Keep in mind, the newer the better. Even a new cat thats had a bad bit of fuel burnt, or slightly poor/rich/lean tune will have glazed the substrate and be useless.

I did this after epically failing with x-force cat.

Stock ecu also.

Ok thanks, good info, I think the 5 gas is a little more lenient than IM240, ill ring a couple places tomorrow about an xr6t cat. I'm running a vipec ecu.

*edit* abr33 is that with and Rb26 and stock injectors or a 25?

i passed the IM240 with a euro 3 cat (euro 4 will be better), 740cc injectors, gt35r, stock cams (big cams will hurt your results), running off a vipec plugin. if its tuned for emissions with a good cat is possible to pass with a fairly modified car.

Most three way Catalytic converters need the tune to be close to stoic in order to keep the cat at elevated temperature and to aid in the reduction of your three gases. This will be difficult with 1000cc injectors. I would also recommend using std 370cc injectors or similar.

If getting a cat, stick with Catco or Magnaflow as these will actually pass an emissions test. Catco have had their's tested with the EPA and have certificates for them whereas knockoffs (X-force which is a copy of a HKS cat for example) don't have a chance in hell of passing. Magnaflow being american and Californian emissions laws I think being even stricter than Euro standards.

thats probably just something they do so its almost guaranteed to pass first time but running 5 cats isnt practical or cheap and you have to get them all up to temp before they work properly anyway, they should always do 2 tests when checking, you will notice the first test is almost always a fail as the cat isnt at operating temp and then they do a 2nd test which has massively improved results as your cat has got some heat into it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...