Jump to content
SAU Community

Recommended Posts

Hey guys

Looking at doing a service on my gtt.

i see so many recommendations for oil/oil filter and spark plugs not sure which way to go.

Dr drift recommends castrol edge 5w30, with bcpr6es spark plugs.

If anyone can concur with this, i mean is such an expensive oil needed?

Would appreciate some feedback

OIL=

OIL FILTER=

SPARKS=

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/403920-r34-gtt-standard-service/
Share on other sites

here you are my good man

oil - motul 4100 turbolight 10w40

oil filter - ryco z145a

sparks - ngk bcpr6es

ive tried a few different oils and such but this is what i stick with now. as for the cost, no one ever said buying/running a skyline would be cheap, and i like to use good stuff for everything

car is always "bubbling" at idle, i get these pops.. it does misfire when i hit the pedal on the way down the rpm

its also misfires heaps when i plant it in second at around 5-6 rpm,

im thinking coilpacks, but do i go a lower spark gap?

mine very rarely pops on idle, but im running a little more boost and thats why ive got 0.9mm gap plugs. as for your car the idle and misfire may well be caused by the spark plugs (maybe) being old and too larger gap, bottom line id try switching back to 1.1mm gap ones and see what happens. spark plugs are soo much cheaper than splitfires, but it it still misfires with new sparkplugs its something you may have to look into

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...