Jump to content
SAU Community

Recommended Posts

Hi fellow stagea enthusiasts and owners,

Seem to have encountered a few minor problems the other week, Long story short it was raining extremely hard when I was coming upto a set of traffic lights. Friend of mine was in the car with me and he screamed all of a sudden for me to watch the curb which I was a safe distance away from, Locked the steering wheel to the right hand side after being shocked and completely surprised and understeered up a curb. As a result of clipping the curb and the car going slightly up it I have annoyingly twisted my left radius rod bush and moved my engine crossmember to the right. By about half a centimetre to a centimetre and bent bolts in the process which hold it I'am led to believe according to a friend of mine and his fellow co workers at his tyre fitting/suspension shop. Need some straight answers because I need to fix these issues before my car is sold as a buyer is 100% interested on purchasing it and I have had to put off the sale unfortunately for a bit.

Questions which I have to ask are will I be able to replace my front radius rod bushes with these aftermarket units in the link without having to go aftermarket all the way around the OEM Nissan bushes I got quoted from Nissan would cost me around $90ea thought I may be able to save a bit of money and time whilst making some improvement by going aftermarket before it's sold. http://justjap.com/s...&cat=398&page=1

Second question is what process is involved in rectifying the issue with my crossmember and moving it back to the left where it should be sitting. Got a quote for $800 off a friend but I thought it was a bit steep and cannot justify spending 800 before the car is sold. Have worked in crash repairs for most of my past career but was a car painter so I don't have much experience in the panel beating section but I know for a fact the job is alot smaller then they claim.

Best regards and looking forwards to your responses Chris.

Edited by hks33

When I fitted adjustable castor arms I sold my stock ones for $30 the pair so you may be able to pick some up cheap. Skyline ones will do too. The bushes you have linked to will do the job - if your castor is the same L and R then you can install the bushes so as to provide maximum castor (it won't be that much) or for similar money you could get fully adjustable castor arms. I'm in NZ so can't help you with the chassis straightening!

From what I'm lead to believe I need the GT-R style ones (4wd) only...

Skyline ones will not work from my understanding. What do you mean in relation to my castor from the left and right being the same shouldn't it be the same all ready?

Yes GTR Skyline - here's some:

http://www.trademe.co.nz/motors/car-parts-accessories/nissan/suspension/auction-490757269.htm

Yes castor L and R should be the same but may not be as a result of hitting kerb and might still be out after chassis straightening in which case you can use the adjustables to correct.

If it is the same L and R then the above arms would be your best bet (simple to fit no press needed).

Do the ones which I added a link to in this thread have to be pressed in?

Yes or you can use a vise but if you don't have access to a press then you have to cut/burn the old ones out. If you are not going to keep the car 2nd hand stockers make the most sense.

With limited Stagea parts for sale currently on the forums I would have thought it would be hard for me to find 1 of radius rod bushes though..

Not second hand bushes second hand rods (Stagea or GTR). If you buy the TradeMe ones linked above it should only cost you about $AU 60 or 70 with postage.

No I understand your problem but it is easier to just replace the whole rod with another than to remove and replace the bush. You could buy the ones from TradeMe, or post up a wanted ad in the Stagea and the general "parts wanted" section of this site or phone around the wreckers

Are these adjustable rods with the bushes pressed in? I'm assuming there's no variant between both manual and automatic.

Could you please PM me a price pretty interested if it's moderately priced.

As for your crossmember issue i may be able to shead some light on that. A long time ago i hit a gutter in much the same fashion (although in a crappy VS ute) and the damage to the crossmember was substantial.

First thing to do is check all the welds on the crossmember. If any are even cracked it must be replaced. Ditto if theres any bent areas.

Secondly check it for square. It will need to be measured to make sure its not warped or twisted in any direction. If it is, it must be replaced.

Finally, the whole car must be put on a rack and checked that the chassis is still straight. Its easier than u think to tweak the rails. Uve mentioned the bolts being bent so theres a good chance its tweaked. Although being in smash repair im sure u would have done most of these checks.

As for the $800 that sounds cheap to me. Personally I'd want to make sure everything is done properly with no corners cut. Otherwise the car will never drive right no matter how much u wheel align it. When my old ute was checked the crossmember was bent, twisted and cracked! It also had damaged the radius rod bush, which later turned out to be a bent rod. As well as a split lower control arm bush. So make sure everything is examined very very carefully.

Edited by Raysboostin

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...