Jump to content
SAU Community

Sth East Subs - Fri 20/7 Or Sat 21/7 Cruise / Meet & Greet? Anyone Intersted?


Recommended Posts

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

hope you didnt take offense at that! i saw a a girl driving a skyline hear narre warren and put two and two together!

nah i didnt go, been too busy working on the old girl. shes 230k old so needed a face lift and some botox! haha! (M bar and some engine work!)

No, not at all. All good - I get asked a lot if was here or there or on this road etc. Lol. Kinda used to it now :) hope the 'face lift & breast inplants' Etc are going oK on the car.. let us know when she's out of surgery & back on all 4 wheels :):cheers:

I'm keen for another one of these. some of my other mates are coming on a drive/meet this coming sunday (the26th)

we are gonna head to Healsville area. I need to take my 34 GTR for a spin. so if anyone wants so come just pm me, cheers

we will be meeting in bayswater.

Damn Healsville. Last time we went up Kinglake, and was enroute to Healsville when two of my mates hit Kangaroos lol - ouch! Hopefully they're hiding in winter :P

Hey, wasn't me :P. I dodged them like a baws.

But nah it was on a dead straight stretch of road where the speed limit was 80 or 100... :/

Start up an event in the events section if you guys want to do it.

Otherwise its just going to be fail like the previous attempts in the last 5 weeks.

Happy to promote the event via the SAU VIC FB page for you guys as well

Guest
This topic is now closed to further replies.



  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...