Jump to content
SAU Community

Tyre Poke

gtsttrk
 Share

Recommended Posts

gtsttrk Mentor

gtsttrk

Posted
Posted

Hey all just got some new Rota rims, p45r2's (18x9.5) all round. Now I knew I was going to get some serious poke, but that Didn't worry me as I'm planning on running wide guards.

However what my problem is the rear wheel on the RHS sticks out at least 2-3mm than the rear LHS.

344c93b4.jpg

Now I was assuming this either meant that my diff was off center or I had a problem with my rear camber arms being off. I was wondering if anyone else had an opinions on this issue, or idea at what the issue could be.

Much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/405297-tyre-poke/
Share on other sites
Hank Scorpio Grand Master

Hank Scorpio

Posted
Posted

A set of rear subframe collars supposedly helps a little bit as it locks those fluid filled rear diff bushes into place that get a bit old and tired.

Oh look, I just happen to be selling some also... :whistling:

But seriously they are meant to make a bit of a difference in the back of the R33s but I can't 100% confirm this if someone else would like to chuck their 2 cents in.

Link to comment
https://www.sau.com.au/forums/topic/405297-tyre-poke/#findComment-6456438
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...