Jump to content
SAU Community

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Running in dyno pull at 20psi of boost pressure. Responding nicely

your dyno guy above is a splitting image of my brother - i shared this clip with my mates & we all had a laugh about it!

Enough said.

538773_10151173938879571_454310209_n.jpg

congratulations - 1430nm is absolutely massive!

my rb26/30 made 930nm on a dyno dynamics dyno - would it be accurate to say that your engine makes in the vicinity of 50% more torque? if so, i don't think i could even begin to imagine how this feels...

not bad Martin, i was expecting the turbos to come on later in the rpm

do you feel that power loss below 3800 on the road? does it feel light switch through the midrange?

Edited by domino_z

Domino, it shows to boost slower than it actually does as we needed to use a faster ramp rate on the dyno to keep full traction at all four.

In other words its not that much laggier than stock, with a massive seam of torque once its 'on'

Quite impressed with this combo actually :)

  • 2 weeks later...
  • 2 weeks later...

Saw this car on display on the weekend, looking good, cant wait too see it unleash down the strip! Let me know when its going to be down there Errol....

Cheers Cale

  • 2 months later...

martin, as you know we have been moving and no time to drive this vehicle. have now had the extreme pleasure of driveing about 300 kilometers and the more i drive it the more impressed i am by the whole package that you have put together for us. the torque is awsome to say the least and it comes on incredibely fast and furious. i will run it in properly over the next couple of months before heading to the local drag strip. the amazing thing is that even with this package the vehicle is quite driveable. thanks for all your help in putting this all together.

martin, as you know we have been moving and no time to drive this vehicle. have now had the extreme pleasure of driveing about 300 kilometers and the more i drive it the more impressed i am by the whole package that you have put together for us. the torque is awsome to say the least and it comes on incredibely fast and furious. i will run it in properly over the next couple of months before heading to the local drag strip. the amazing thing is that even with this package the vehicle is quite driveable. thanks for all your help in putting this all together.

Make sure you let us know when it is going to the strip please errol

  • 2 months later...

Sure will Errol. Domino, in short Rooters car is a built Trust 3.8 engine with ported heads equipped with a TD06 turbocharger kit, Syvecs management, and all the fruit to make it run good power on E85 (2000cc injectors etc.) If you want a detailed, detailed list then let me know. Its a nice tight combo, and the TD06 kit is one of our favourites, as not only does it work well, but its engineered for RHD GTRs unlike most anything from the USA (big consideration that one if you dont want to spend extra money fixing steering rack clearance issues) :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good tips, will get on those tomorrow. When doing the maintenance I did move a few of those connectors around, and things that are old tend to not like moving around. (Like me).
    • Don't try it. It will be shit. Better chance of damaging the engine than gaining any knowledge about the old one. Maybe, but unlikely, especially if the O2 sensor is working. You can use NissDataScan to look at the stock ECU.   Cleaning the AFM is seldom necessary and seldom helps. The R35 coil & loom conversion should eliminate dud coils or plugs. But as you still have misses - look to the plug where the coil loom connects to the engine loom, and the CAS plug. Need quality connections there. Also look to injector plugs. And the AFM plug while you're at it. Also look to whether your injectors are clean and flowing evenly. Get them out and onto a testbench.
    • Good to know, I feel like I am in for a rollercoaster ride that looks like a sine wave. 
    • You'll fit right in. Acceptance is the first step.
    • Hey folks. I've been lurking and browsing the forum for a while, since I got into my head that I wanted a skyline. Having purchased an overpriced completely stock GTT, (only "mods" it has is HKS pod filter and catback) now that it became legal in the US, it was all glorious and sututu noises here and there. But then I wanted to do things right and went to do basic maintenance. After all the fluids, filters done, I did the spark plugs, that's when the problems started.. First the car started spluttering at around 4.5k RPM. Which I gapped down the new plugs and that solved the sputter there, but the car now always misfires at idle with pops when lifting off and shifting 2nd to 3rd. Similar to the issues in this recent thread. I've been banging my head against the wall, reading the threads here and trying suggestions for a couple months now, so decided to start this one to explain exactly what I tried and what is going on. The symptoms of the issue: Idle and low revs misfiring intermittently. You can hear the exhaust tone change and the shakes on the shifter knob. It happens frequently, but doesn't seem to have a rhythm to it. Pops when backing off throttle. It pops and or burbles almost feels like it spits fire when it pops. (Happens mostly in 3rd gear at around 2k RPM). When under load and after 6k RPM, it also pops when shifting from 2nd to 3rd. There's a ticking noise at around 2k RPM in 2nd gear going downhill, seems unrelated though but I am out of educated and downright dumb guesses. Not noticeable lack of power when putting the car into load. The attempted diagnosis and solutions: Unplugging coils when the car is running This did nothing to change the idling and tone shift for every cylinder. Checking the exhaust headers with thermometer They all are within what I'd say it is margin of error of the laser thermometer New spark plugs Tossed two new sets, copper, iridium and using the old ones, still misfiring, even re gapped to 0.8mm, still same thing. MAF cleaned with the "specific" spray cleaner No changes in the issues what so ever. Brand new loom and r35 coil conversion (was going to add the r35 coils anyway) car runs arguably better, still misfires, but seems like does less frequently. Placebo? Code 21 now being thrown, thanks nissan gods. Removed the CAS to check the shaft for play or anything. CAS seems all fine, nothing that indicates any issue, visually speaking. Things to attempted next: Ordered a new MAF (chinesium from Amazon, to be able to return regardless of result). Fuel with proper gas, maybe it is this California water that they sell as gas that is to blame? Plugin the link ECU and check the info using the built in base map. Go back to BMW and eat my rob bearing breakfast without milky oil mixture.   Do any of you have experienced anything like this or have any suggestion?
×
×
  • Create New...