Jump to content
SAU Community

Recommended Posts

Hi

I'm having a minor issue with cold start when the car has been sitting for a while. I wasnt to worried about it but recently I went overseas for nearly 3 weeks and when I got back the car would only just start and ran horribly for about 5 mins

normally but it will either fire first time and die straight away, then next time it fires up alright and idles perfect

Or

fires up, idles jump up and down about 500rpm (between about 500-1000rpm) a few times then it idles perfect.

I had a FPR laying around so decided to change mine in the off chance something was wrong with it. When I pulled mine out I noticed the fuel was slowly bubbling as if there was air trapped in the rail. Left for a while there was no fuel visible through the hole for the FPR

So it looks to me like over time the fuel drains back through the pump to the tank, but I didnt think this should happen. Was fairly sure the pump has a check valve to stop this happening inside it (I have a Tomei intank pump, same as Nismo)

Car also has 555cc Nismo injectors and 255rwkw. Fuel filter replaced not to long ago (Z201 from memory).

I'm wondering if the check valve in the pump has failed or something, or if perhaps I'm missing something.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/405301-starting-problem-air-in-fuel-rail/
Share on other sites

Its a good way to diagnose if its too rich or too lean. If holding the throttle open helps then its too rich on start up. If hinders then too lean.

Makes sense :)

I'll try and remember to do that next time I start it in the morning

can you confirm theres a check valve/anti return valve in the Fuel pump to stop fuel flowing back through it?

I'll have a look tomorrow (if I remember) and make up a little jumper lead to earth it to chassis.

Or I might just do the full re-wire while I'm there

But I have tried priming the car constantly before startup (If I hold my key just before it starts the fuel pump constantly primes) with no improvement

But worth a shot anyway

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...