Jump to content
SAU Community

Recommended Posts

Dude you don't have to break the pump to spin a bearing. They have oil control issues from factory which causes bearings to spin. Plus its an old engine with god knows how many km. Factory didn't do too well in that area.

Im pretty sure a RB26 lasting 20 years

with god knows how much abuse it has received and the unknown km it has traveled, including all the launches it must have done, and red line pulls,

Is pretty damn good.

I know mate, that's why I said it depends which one he has. Do you think it's worth the trouble to change the oil pump on its own? All that work! If it's the late model one just leave it, even if it's the early model pump Its not worth all the work and trouble unless doing other things too.

I completely agree. No point changing oil pump until the engine is on its last legs. unless you're cashed up.

I was only emphasising "Factory didnt do well"

Lol sorry man I didn't express myself correctly, I know what you mean. I wasn't trying to say they were shit like I came across. I agree with you!

Regardless of your future plans for the car and If it is dead stock try these two and see how you get on.

Do a hot oil filter change.

Do an air filter element change.

Reckon then your first items would be a filter relocation kit and pods.

Lol, Have done it twice now, all you need is skill

IMO changing the oil pump is not justified cost/benefit wise, since, as stated, its an engine out job. Just don't hit the limiter and replace the harmonic balancer if its stuffed. I'd be more inclined to change the turbos, but then again, my oil pump hasn't failed and my turbos have...

Other than that just the normal stuff, so fluids, cam belt (and the associated idler and tensioner) if its anywhere near due (or if you dont know).

Those of us who drive completely stock 32 GTR's (not 33 or 34) would know the hydraulic HICAS valve bank makes changing the oil filter a mission. Filter can't be seen from above or below.

It also requires an AFM and boost pipework to be removed just to check an air filter.

I'll always put ease of maintenance ahead of modifications.

Obviously the FIRST thing any new owner should do is get the workshop manual and start reading.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...