Jump to content
SAU Community

Recommended Posts

I Have recently written of my 34 4 door gtt,.. I have purchased a gt and swapped my manual trans and engine from gtt and put into gt shell, so I have a combination of parts available from gtt and gt. series 1 (1998, 2000 models)

ITEMS NOT AVAILABLE ARE:

MOTOR, MANUAL BOX AND TAILSHAFT, CLUTCH PEDAL/CYLINDER, BRAKES/HUBS, and various other bits that have aready been sold.

All items are located in Adelaide hills (pickup preffered) can post at buyers expense, but will have to bear with me, I work two jobs and it can take a few days to pack and get to a post office due to this. I am open to reasonable offers and prices are not 100% firm, but please no low ball offers, time wasters AND IN THE SAKE OF KEEPING THIS THREAD CLEAN PM ME, OR EVEN BETTER SEND ME AN SMS OR PHONE CALL FOR A PROMT REPLY!!! I AM IN NO HURRY TO SELL ALL THIS< JUST THOUGHT TO START CLEARING BITS OUT SO PLEASE DO NOT WASTE Y TIME WITH STUPID OFFERS OR SAY YOU WILL PURCHASE OR COME UP AND THEN NEVER FOLLOW THROUGH- I AM VERY BUSY AND DONT NEED HASSLERS. THANKS :)

GT Air box with Snorkel $40

Gt Automatic gear box with tailshaft $200

GTT Airconditioner Compressor $100

GT/GTT/GTR headlights pair $400

RHS fender $150

2 x LHS Fenders (both have a small lip on the edge from tyres nothing major) $150 each

Bonnet (has several hail damage dints, would most probably need to be resprayed by new owner and remvig them would be an easy and cheap job) $180

GT front bar $150

Pair of GTT headlight Brackets $20

Pair of GTR headlight backets (needed for GTR front end conversion) $150

GT bonnet catch support $20

GTR bonnet catch support(needed for GTR front end conversion) $100

GTR bonnet hinges (both slightly bent from accident- id imagine a hammer and a vice and all back to normal- make an offer)

GT front reinforcement bar $80

pair of frot bar orange indicators $40

Pair of fender orange indicators$10

ABS Unit $150

Carbon canister $20

GT Dash (No Vents) $50

GT Auto dash Custer (just cicked over 100,000 kms) $80

Carpet $80

Seatbelt (set of 5 with rear buckles)$100

Door locks and ignition barrell with key- have lock box also if required for remote key) $100

Drivers door $150

Drivers door card (speaker painted silver and handle surround) $20

Passenger door$150

Passenger door card (speaker painted silver and and handle) $20

LHS Rear door card $20

LHS Rear door glass $40

LHS Rear door window switch $10

RHS Reah door card (painted handle silver $20

RHS Rear window switch $10

RHS Rear door $150

Drivers door window/mirror switches, (painted silver) $40

Passenger door window switch (painted silver)$20

Sunvisor pair $20

Parcel shelf $20

Roof lining $40

Boot lid with spoiler holes$100

Spoiler $50

Boot carpet $20

Space saver rim $40

Boot lining $50

Drivers scuff panel $20

Passenger scuff panel $20

RHS Rear scuff Panel $20

LHS Rear scuff panel $20

A Pillars pair (re fabricated) $20

B Pillars Pair $20

C Pillars Pair$20

Pair of what i beleive is the fogdriving lights that sit next to the indicators in some gtt front bars $50

RB25DET injectors (115,000 km old) make an offer

RHS Tail light $100

LHS tail light $100

Rear bumer (minor mark will come out with respray) $150

Series 2 factory plastic rear pods $200

Series 2 Factory plastic side skirts $200

Weather shied set $100 slight damage to one

Rear windscreen $100

Tripple gauge cluster (gauges only) $40

Hicas computer make an offer

Hicas unit $50

Heater $100

Roof handles set $20

Front steering rack- with crossember and sway bar $300

rear subframe (yet to remove)

Diff (has the one ABS sensor- not the one with two sensors $250

Handbrake with cable $80

SRS control box, make an offer

Steering wheel with airbag GT auto (some wear) $150

RHS Lower Control arm $50

LHS Lower Control arm $50

RHS castor arm $40

LHS castor arm $40

GTT dump pipe make an offer

Nismo exhaust (think its a 2 1/4" il have to check) cat back(knocked out cat)suit N/A $350

Rear seat $150

Front seat pair-no seat belt buckles (will sell once they have been dry cleaned to remove some grime- should be done in a week or two) $300

rear reinforcement bar$100

body loom make an offer

headight loom make an offer

inside fuse box $10

fuel flap $20

GTR ( the small reo bar that attactches to the headlight brackets and sits under where the top of the bumper goes) $40

GTT (the same bit as above but GTT)$20

GTR ( plastic strip with rubber on it that sits on top of gtr bumper $40

GTT below headlight brackets (pair) $50

GT NEO engine cover $10

GT fuel pump make an offer

GTT brake master cylinder and booster $150

mat set $80

have a gtr front bar thats been damaged in accident (make an offer) can mms pics repairable

Aftermarket rear adjustable upper arms - unsure of brand $50

Hicas lock bar (unsure of brand) $40

There is probably bits I have missed feel free to ask away- have sold a lot of interior bits hence not listed.

have various bits,like control boxes etc under dash, looms, bits n pieces, various brackets...ask away.

SHELL IS WRITTEN OFF and at this stage has a home.

Contact me via sms/phone please if possible 0419837474

Cannot be bothered uploding a pic of every part in here so can email and mms pics if required.

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

Both door handles?

Can take the front two off for you? Have front and rear rhs passenger.lhs crushed. Assuming won't need locks-would rather keep locks as a set with ignition barrel and key. Pm me thanks.

Rear pods sold

Sideskirts sold

Headlights sold

Hicas lock bar sold

Rear adj arms sold

Gtr front end parts sold

Boot carpet sold

Rhs gaurd sold pending payment

Few other bits on hold..

Airbox sold

Snorkel sold

Rhs gaurd sold

Engine cover and bracket sold

Also to add for sale is:

Brake master cylinder plus booster

Rear window wiper plus motor

Air flow meter

Possibly chasing the fuel tank lid and the 2 wire wiring loom between the fuel pump and fuel tank lid and about 200 mm of wiring prior to the fuel tank lid.

Got em both.. Send me a text if keen. Looms out of shell. I presume you mean the cap on tank where hosing and plugs go into for pump?

Yeah bud-auto clock spring but can make it work on manual wheel if u cut/splice just the horn wire. SMS me if ur keen as I don't check this daily.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...