Jump to content
SAU Community

Recommended Posts

hey guys im a bit of a skyline/car noob so bare with me :)

this afternoon i went to take my 33 out for a drive as i havent had the time in the last week and first off my battery was drained, which i guess was caused from the alarm system in it, maybe a light or door left open but thats not the problem,

when i was trying to get it going i tried to jump start it down the drive way i didnt do it a whole lot or very far but just tried twice to get it going then afterwards just decided to start it using a different battery and then replaced mine back in to recharge, anyways when i went to put it in gear i noticed when i engaged the clutch it had a loud strange whine/whirr?? another person with me thinks its more of a grinding but i dont think so

i let it sit for a while to charge the battery probably 30mins? (side note...heard rumors leaving skylines sitting in one spot for long periods is bad? is this the case as it did get pretty hot in there to the point it was making the ticks you get on a hot engine when turning it off)

after it charged i took it for a drive to see if the noise would go away, if i was riding my clutch the noise wasnt there but if i had it fully engaged it was there, sometimes it would be loud sometimes barely noticeable....

does anybody know what this could be? the last time i drove it, it didnt have this noise but now all of a sudden it did after the battery went flat....

Link to comment
https://www.sau.com.au/forums/topic/407155-strange-clutch-noise/
Share on other sites

Clutch throwout bearing.

On a side note, you can't rollstart EFI cars if the battery is totally dead. Sometimes you can if it's just a bit too flat to crank, but still powers the car up.

On another side note, leaving any engine idling for extended periods is bad. Just stick a thin piece of cardboard behind the throttle stop. Keeps revs higher, better for the engine and will charge the battery a lot faster as well.

thanks oem....yeah i thought leaving it for that long might have been a bit bad so took it for the drive just so it had a bit of air flowing

throwout bearing....what would have caused it to just break when the car hasnt been driven? do you guys have a rough idea of where i can buy a bearing and how much itd cost roughly in labour at a mechanics??

Its not the airflow, its the oil flow.

Throwout bearing is roughly $20-$30 from any auto store. Problem is you have to pull the box off to change it.

If its only doing it occasionally just forget about it and change it when you next do your clutch.

im pretty sure it only does it just while the clutch is pressed in....would be annoying at a set of lights i could imagine would feel like im doing damage to something the whole time im sitting there lol...but while driving its barely noticeable. Can it cause damage if i leave it ?

if it can cause damage, would i be better off just replacing my whole clutch straight away?

Its not really going to damage anything. However, if you think it sounds quite nasty, get it changed. If you have changed your clutch recently then don't worry about the clutch, just get a bearing. If you've had the car for a while and the clutch is of unknow origin and age, change the lot.

From what I have seen, with general road use, the bearings normally either outlast, or die around the same time, as a clutch. And they are usually changed with the clutch, so if the bearing is dead, clutch is usually getting close too. Just for your thoughts.

thanks again mate, ive only recently bought the car in the last few months so im going to assume the clutch is old and worn, its all pretty much stock....what clutch would you guys recommend for a every day driver/take a decent amount of power ? something that is good for stop/go traffic....

I had a Exedy Organic in my old car. Bought from Kudos Motorsport in the FS section. They are genuine kits unlike some of the mix and match kits that are around. Anyway, the new owner of my car pushed over 320rwkw through the clutch before it let go. Not bad for an organic with nice soft engagement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...