Jump to content
SAU Community

Recommended Posts

I have an R34 GTV.

I Crashed it back in feb, wen up the ass of an Astra. Her reo being higher then mine did a bit of damage.

So, ~4mnths later after getting parts and $$ back on the road.

Now, first day I got it back, the gearbox kicked like a mule. Changing gears in auto or tiptronic was rough as guts.

Couple days into it and it's much smoother but the A/T light was flashing on startup so I took it to a mechanic and he took the fault code off the ECU for me, the resulting code:

10 Line Pressure Solenoid Problem.

Now his advice was to take the car on the freeway and go through the gears, the logic being that the solenoid is "sticky" after having sat for so long, which was pretty much my idea too.

If that fails flush & change trans oil.

If that fails take out the solenoid and clean it.

Sound about right? Any advice? Any recommended guides for doing the change on the trans?

Thanks,

Teir.

Link to comment
https://www.sau.com.au/forums/topic/407216-10-line-pressure-solenoid-problem/
Share on other sites

Drpping the sump won't do it. Take off a cooler pipe and run the engine till you have filled a 2 L container. Pour 2L of pref synthetic atf down the (auto) dipstick holder. Repeat until the new fluid comes out - you will need about 12L so probably buy a 20L container.

I had some major slipping and jolting with my auto at Sandown last week, it turned out the mesh filter in the sump was completely blocked. I dropped the sump, removed and cleaned the filter off the valve body, and refilled with fluid, with no issues since. Shame I didn't clean it when I put the new converter in two weeks ago, I wasted over a bottle of synthetic fluid.

I have noticed firmer changes after changing the fluid, the Dextron III that was originally in it from the rebuild must be thicker than the Nulon synthetic at operating temperature. The thinner fluid definitely firms up the shift by filling the accumulators quicker.

Thanks heaps for the info guys.

Seems the light has stopped flashing.

Gear changing is medioka, still a bit rough and 'jolting' sounds like the right word.

@Scotty, How hard is it to take apart the sump and clean the filter? Or is it similar to changing the oil filter on the engine?

@KiwiRS4T, Wouldn't you use one of the products around that are supposed to flush the old fluid out of the gearbox instead of wasting so much good fluid? Or am I making things up? lol

Thanks heaps for the info guys.

Seems the light has stopped flashing.

Gear changing is medioka, still a bit rough and 'jolting' sounds like the right word.

@Scotty, How hard is it to take apart the sump and clean the filter? Or is it similar to changing the oil filter on the engine?

@KiwiRS4T, Wouldn't you use one of the products around that are supposed to flush the old fluid out of the gearbox instead of wasting so much good fluid? Or am I making things up? lol

Its fairly easy to drop the sump. The filter is steel so no need to buy a new one just take it out and clean it. You're not wasting good fluid - that's how much is in there (mainly in the torque converter)!

Its fairly easy to drop the sump. The filter is steel so no need to buy a new one just take it out and clean it. You're not wasting good fluid - that's how much is in there (mainly in the torque converter)!

Awesome, ok.

Doesn't seem too bad, found a couple of good videos too on how to go about it,

So I'll use that as well.

What should I be using to clean the filter? Just a rag or any products? As well as the sump tray, cause I'll have to clean that as well when I take it off ey?

Lastly, any recommendations for the fluid? The stuff mentioned in the thread seems like overkill for a N/A Auto R34. Especially if Kiwi reckons i need 20lt of it. The Castrol Transmax Z they're talking about is $75 for 4lt!

You should only use the nissan fluid if it has the stock clutches, mixing fluids isn't recommended and as said the torque converter will still have a few litres in it you cant get out.

I cleaned the filter with ethanol but petrol/kero would work well. Make sure you lay the filter bolts out in order, they will have to go back in the same hole they came out of.

Run a thin bead if silicone around the pan gasket when you reassemble and try not to drive it until it cures.

It would be a good idea to put down a plastic sheet first, you will make a mess.

You should only use the nissan fluid if it has the stock clutches, mixing fluids isn't recommended and as said the torque converter will still have a few litres in it you cant get out.

I cleaned the filter with ethanol but petrol/kero would work well. Make sure you lay the filter bolts out in order, they will have to go back in the same hole they came out of.

Run a thin bead if silicone around the pan gasket when you reassemble and try not to drive it until it cures.

It would be a good idea to put down a plastic sheet first, you will make a mess.

Well the car is second hand, so god knows what's in it, hence the need for a full flush. and silicone? Just the normal silicone you can get from the hardware store? ie gap filler?

Awesome. I'm on track now. I'll have to have a good look under the hood and spend some $ to get a couple things but I'm not too worried about doing it myself.

One last question, since I'm taking apart the transmission sump is it worth me cleaning the solenoids anyway? Are they accessible after taking the oil pan off? If they are I might as well do that too while I'm there.

  • 4 weeks later...

So, a trip to the trans specialist and $800 later, I have 4 new solenoids, a new filter and obviously fluid. But still a flashing A/T light on the console on startup... Going to see him again on Monday to get him to read/clear the fault and see what happens, but any ideas?

He did "apparently" test the solenoids before replacing them...

Or is that now obviously bullshit?

And since they have been replaced, any ideas on what the problem could possibly be?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...