Jump to content
SAU Community

Recommended Posts

On the 1RM, what is a good way to test that out? ie after you have stretched, warmed up etc how many sets, what weights should you do before you try and hit the 1RM or doesnt it matter?

I tried bench on Monday but I 'think' I did too many sets first?

60x12

80x10

100x6

110x4

120x1 - this was the 1RM effort - spoilt by a spotter who jumped in at the first sight of struggle, despite being told not to!

Cheers.

Been a while but finally managed to work out some 1RM's;

120kg bench

165kg deadlift

110kg squat (no comments lol)

Decided my starting weights on the PPP are going to be;

130kg bench

180kg deadlift

120kg squat

I figured that if I go through the program and it becomes too much on a certain week I will drop to the lower weight program for that week and do the weights stated there. I didnt want to start too low and not gain much overall improvement on the PB.

So started the deadlift PPP yesterday and was OK. Lower back feels it today. Today off and tomorrow chest.

Squat and deadlift are great. Bench is a bit low compared to them, any reason? What do you weigh again?

A competition bench is done with a pause on the chest, bum on the bench, feet cant move

Many that have lifted at my novice comps are stunned how much they lose when they have to it properly

That will be a great total Nick at sub 90kg, 565kg at your first States is great. Max did 462.5kg at his

Very different to a gym lift

Many that have lifted at my novice comps are stunned how much they lose when they have to it properly

Although it's sometimes a downer first time you try, once you learn how to do it properly it eventualy helps you lift more. Most people don't drive through their feet etc.

Edited by rev210

Oh, I agree. Max's PB is 155kg paused, he's never tried more touch and go. In fact he pauses all his reps now

Gym lifters drop over 10kg when they try to pause, some drop another 10 when they have to touch there chest

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...