Jump to content
SAU Community

Recommended Posts

The most I got to on SLDL was 120x10 before switching to off the ground. They were certainly tough, particularly on grip because you can't rep reset like off the ground. Great for people with limited flexibility too.

Do you guys do any grip specific training or just let the compound pulls do their work over time? Is there such an exercise as just standing there in a lockout until your grip starts to give way?

Didn't do the week 11 of the PPP 180kg deadlift but did the following;

60 x 5

100 x 5

140 x 5

150 x 3

160 x 3

170 x 1

180 x 1

Got my 180kg PB! It was nice seeing 4 x 20kg plates each side lol. Am absolutely wrapped with that.

Weighed in today at 78.9kg so lightest I have been in 15 years yet have lifted more than I ever have.

Didn't do the week 11 of the PPP 180kg deadlift but did the following;

60 x 5

100 x 5

140 x 5

150 x 3

160 x 3

170 x 1

180 x 1

Got my 180kg PB! It was nice seeing 4 x 20kg plates each side lol. Am absolutely wrapped with that.

Weighed in today at 78.9kg so lightest I have been in 15 years yet have lifted more than I ever have.

it's a good reward when you see the numbers go up

Didn't do the week 11 of the PPP 180kg deadlift but did the following;

60 x 5

100 x 5

140 x 5

150 x 3

160 x 3

170 x 1

180 x 1

Got my 180kg PB! It was nice seeing 4 x 20kg plates each side lol. Am absolutely wrapped with that.

Weighed in today at 78.9kg so lightest I have been in 15 years yet have lifted more than I ever have.

Grats dude! :)

192.5/100/210 - 502.5 at 87.9kg

2.5kg PB / 10kg worse than PB / 10kg worse than PB.

5kg lighter bodyweight.

Happpy with the sq PB.

The others are still weak but it's as good as I could get them since last injuries.

Hoping to improve SQ and deads by June.

Bench will prob stay the same cause I won't be training it much if at all.

Once again, I hate wraps.

so so much pain.

.

Edited by TTT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Thanks GTSboy. I will inspect the valves actually, is this something I can do while they are still in the head? The block/bores don’t look bad to be honest hey, I can still see the cross hatches in the bores and they still measure 86.5mm. I’m not sure how to measure the installed ring gaps but I will do that and take it to someone who can. 
    • I’ve had the same headache with my lowered car, scissor jack first then floor jack every time. Ended up grabbing an extra-low profile aluminum jack (about 70mm entry height) and it finally slides under the lip without drama.
    • No sync errors , i have installed AEM disk will return original 360 slot disk and check if there’s any one with running AEM disk could share setup 
    • Its been a while! Finally thought to do something on this car, so here we go. This will be a slow burning, multiple posts as I spend 0.5-1hr a day on this job, over multiple days... Full set of GKTech suspension arms!   Step 1: Buy Arms, done! Step 2: Start removing stuff. HICAS was easy. Rear suspension arms are now gone, they were a bitch but breaker bars with long handle extensions, 2 1.5hr slots later, stock arms are off! Next step, remove the hubs and take them to work to press out the bearings and bushings!  
×
×
  • Create New...