Jump to content
SAU Community

Rb25Det Box To Rb25De Neo Motor

s13neo
 Share

Recommended Posts

s13neo Contributor

s13neo

Posted
Posted

Hey fellas, couple questions

Will a 25det box bolt onto a 25de neo motor?

getting a new clutch/fly, should i be asking for a 25det or a 25de neo clutch/fly?

is it worth replacing the throwout bearing while its out and spigot bush?

the motor is out of an auto, is their anything im missing here, needed for a manual box, besides slave?

Im needing gearbox bellhousing bolts, can anyone link me to a thread with specs or part numbers to possibly buy new?

Got my mind set on a cushion button, can anyone give anyfeed back on this type of clutch?

Cheers Matt

Sorry for noob q's.

Link to comment
https://www.sau.com.au/forums/topic/408648-rb25det-box-to-rb25de-neo-motor/
Share on other sites
Miguelone Grand Master

Miguelone

Posted
Posted

All RB's use the same clutch/flywheel. All RB's use the same bellhousing.

Do the throwout bearing and spigot bush if it makes you feel better, not urgent unless they're f**ked.

Other things you need... Clutch lines, fork, master, pedal.... I'm assuming you probably have a previously auto engine going into a manual shell?

These are the Nissan part #'s for bolts you need, will be about $30 all up.

0112105121 You need 4

3137715U00 You need 3

3137715U01 You need 1

Haven't used a cushion button clutch so can't comment on that.

The Dan Grand Master

The Dan

Posted
Posted

All RB's use the same clutch/flywheel. All RB's use the same bellhousing.

Do the throwout bearing and spigot bush if it makes you feel better, not urgent unless they're f**ked.

Other things you need... Clutch lines, fork, master, pedal.... I'm assuming you probably have a previously auto engine going into a manual shell?

These are the Nissan part #'s for bolts you need, will be about $30 all up.

0112105121 You need 4

3137715U00 You need 3

3137715U01 You need 1

Haven't used a cushion button clutch so can't comment on that.

That is incorrect. The turbo Neo uses a pull type clutch whereas the non turbo Neo uses the earlier push type setup. The bell housings have the same bolt pattern but they are most definitely not the same bell housing.

The Dan Grand Master

The Dan

Posted
Posted

However to answer this guys question, the turbo Rb25 gearbox from an R33 will bolt up and uses the same clutch as the N/A Neo.

You need to get rid of the auto spigot from the back of the crank and put in the bronze spigot for the manual instead. The tail shaft is also different so you will need the turbo shaft

Miguelone Grand Master

Miguelone

Posted
Posted

That is incorrect. The turbo Neo uses a pull type clutch whereas the non turbo Neo uses the earlier push type setup. The bell housings have the same bolt pattern but they are most definitely not the same bell housing.

Ah yeah forgot about pull/push. I know the bellhousings are different, I just meant as you said that they will all bolt up.

s13neo Contributor

s13neo

Posted
  • Author
Posted

cheers guys

got a rb25det box now, has fork, throwout and slave with line

and yes the motor was in a auto.

this is going in my s13 so tailshaft and what not will be different

cheers for the part numbers but they only sell them in packs of 10 so i cant just buy one bolt on its own ect

which eats dick

The Dan Grand Master

The Dan

Posted
Posted

cheers guys

got a rb25det box now, has fork, throwout and slave with line

and yes the motor was in a auto.

this is going in my s13 so tailshaft and what not will be different

cheers for the part numbers but they only sell them in packs of 10 so i cant just buy one bolt on its own ect

which eats dick

I'm pretty sure they are M10 x 60mm or 65mm. Measure the bell housing thickness where the bolts go through and add 15mm then add a spring washer to your bolt. That should give you 12mm of thread.

The Dan Grand Master

The Dan

Posted
Posted

new i read that elsewere, cheers guys

had another guy call saying he has manual rb25det belhousing bolts for 60 posted

bit rich but cbf stuffing around

cheers matt

I've got some second hand gear oil in a pan somewhere you can have for $10,000 if you couldn't be stuffed going to Repco?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...