Jump to content
SAU Community

Recommended Posts

hey guys

i have been looking into this for quite a while, and im about ready to give up, i hear alot of cars having alot of flutter etc when changing gears etc...

and alot of people have been saying it the blow off valve, and alot of people are saying its turbo/compressor surge. just wondering which one it really is.. because hell i think it sounds cool, and would really like it on my r34. and if it is turbo surge, some also say its fine and some say it bad etc can anyone give me some more insight please?

any opinion and help woule be greatly appreciated

Conz

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/
Share on other sites

It is compressor surge and is caused by the bov. When the bov doesnt open at the right time or doesnt open enough the compressed air flows back across the blades of the turbo and out of the air/pod filter. This is often because of the spring rate in bov. It is not good for the turbo because the blades can get damaged and break and go through the engine. The flutter may sound cool between gear changes but its not worth it.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6520961
Share on other sites

The R34 has a nylon compressor wheel which makes them lighter and quicker to spool... yet weaker under high psi/temperature. They're only good for about 10psi and are probably one of the worst turbos to experience compressor surge with. You could get the factory turbo hi-flowed, where they replace the inlet and exhaust wheels with steel. But even so, I wouldn't recommend compressor surge on any turbo.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6521860
Share on other sites

There's a few different forms of surge most common is when the throttle and bov are closed while boost is still in the system with no where to go and it back tracks to the comp wheel and trys to stall it while the turbine is still being driven making that lovely flutter sound which is very bad for the turbo. It puts over 100 lbs of load on the thrust bearing which only has a 2mm contact area in some cases and so they fail quickly.

The other type (shown in the video) is a mismatch of compressor wheel in relation to setup as in its outside its efficiency zone or surge limit and it cant grab air to make boost if it gets to bad it can have a servere enough effect to brake cranks or engine mounts.

Pretty much most blow valves on the market today are crap inducing surge when the stock one worked perfectly fine there is others ways to do systems that dont need a blow off valve - red top RB20's/rb30 VL

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6522997
Share on other sites

This topic comes up once every couple of weeks, use the search function.

People are usually divided when it comes to whether turbo flutter is bad or not. Some people have been running fluttering turbo's for many years with no problem, others blow turbo's and quickly blame turbo flutter when it could have been many other reasons.

This is just my personal opinion, I have had a slight flutter on my ceramic turbo R34 at 12psi for 4 years now with no problem at all. I have read recently the smaller turbo's don't have the surface area that back pressure can damage as easy as larger turbos as the larger blades would be more susceptible to shear forces, but then others say the flutter in smaller turbos is dangerous. Whatever.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6526852
Share on other sites

No one knows for 100% sure if it damages your turbo-charger. It is nothing more than a speculation.

All you have to do to get the sound is block off your blow-off valve. Instead of the air venting via the blow-off valve, it travels back through the intake across the blades of the turbine spinning forward. The resultant noise you hear is commonly referred to as flutter.

Don't listen to most of the tools here saying not to do it. If you like the sound, then do it. Nothing more than personal preference.

As stated, no-one can prove if it actually damages the turbine blades. XR6 Turbo Falcons do it from factory with nothing more than a pod-filter - you do not need to close the blow-off valve.

My brother had an R33 making 450rwhp, running a GT35R and a closed blow-off valve for the flutter sound. No problems ever reported there and that was over the course of 75,000km's.

It's quite simple; if you like the sound, do it.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6527641
Share on other sites

I had a few skylines one with a 35r forged engine etc and blocked off bov because the sound annoyed me had no dramas!

Also stock 25 with a 3076, blocked and that's still going with no dramas! Personal preference but on stock turbo set ups not worth it!

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6527764
Share on other sites

I tell people not to listen to the tools who tell them its ok to do it on their cars which cost them xx thousand. But what do I know? I happen to get my information from people who rebuild turbo's for livings and not off google.

So what if it didnt happen on your car, it may happen on his. And if you want to be the idiot who told him it was ok, thats on you.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6534212
Share on other sites

I tell people not to listen to the tools who tell them its ok to do it on their cars which cost them xx thousand. But what do I know? I happen to get my information from people who rebuild turbo's for livings and not off google.

So what if it didnt happen on your car, it may happen on his. And if you want to be the idiot who told him it was ok, thats on you.

good to know u get your info from people in the loop but gathering information and having it on your car is a different story, like i said, personal preference, your car do what you want!!!!!

his is stock, my set up was aftermarket and yes im the idiot who blocked my bov, BOO FU**ING WHO

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6535611
Share on other sites

  • 4 weeks later...

Meh, BOV sounds are good for one thing and one thing only, creeping up to bus stops when school finishes and all them kiddies are standing around, then as u get closer, boost it hard and blow it off righttttttt next to the bus stops. Hks SSQV/ Turbosmart Supersonic <3

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6571668
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...