Jump to content
SAU Community

Recommended Posts

I have read a lot of things about the Splitfire coilpacks and they seem to be the go for replacement as mine are starting to die under boost. But i heard people only buying the splitfires because the OEM ones were too expensive.

But it seems the OEM ones are 90$ each which ends up cheaper than the splitfires, would you guys recommend them over the splitfires ? Say for higher than stock power running 20psi boost, or is the splitfires better for non stock skyline.

Also i read that these clamps were good but i cannot remember where i read it from, worth the 50$ for 10 ?

http://www.autopartswholesalers.com.au/products/hose-clamps/norma/norma-constant-tension-hose-clamps/normaclamp-torro-ct-constant-tension-worm-drive-hose-clamps-packs-of-10-

Link to comment
https://www.sau.com.au/forums/topic/408860-coilpack-and-clamp-choice/
Share on other sites

I got some brand new OEM coils for about $500 a set and am running them at 20psi soon to go to 25 psi. Someone said there are some fake OEM around but mine seem fine (bought them off an Aussie on Ebay).

Have you verified theres a problem with the coilpacks? If its an assumption, start with plugs first because there a lot cheaper and you already have good coilpacks. What gap are u running? More boost means smaller gap.

These are from Kudos so i trust they wont stock fake ones!

I change my plugs every 5000kms and use copper plugs gapped at 0.8mm. Quiete often when i gun it and it revs in the highs like 4500+ the car will just die for a second.

And my coilpacks seem original with my 100k+ kms and they have been siliconed in the past.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...