Jump to content
SAU Community

Recommended Posts

Well, being the genius that I am, I decided that the easiest & cheapest way to install an oil cooler to my car was to buy one off eBay...

Please queue up in the line to the left in order to laugh at my expense.

And I do mean expense. :O

I bought an eBay oil cooler kit for $135 (posted) back in June with the plans of fitting it up & being awesome.

The pics looked like this:

1.jpg

: with the plan of routing an oil to air oil cooler core from a sandwich plate between the oil filter & oil to water oil-cooler sandwich plate thats already fitted to the block.

Then I received the 'item' some 10 days later direct from Shenzen, China. w00t!

This is what it looked like in the box when I opened it:

IMG_1877.jpg

As you can see, it's got a relocation kit... not really what I wanted, seeing as though theres a poofteenth of nothing when it comes to space for relocating your oil filter in the engine bay of an M35. :wacko:

So I complained that I didn't get what I ordered & was contacted various girls named 'Michelle' & 'Brandy' in Guangzou to address the fact that I hadn't received what was in the picture (being a simple sandwich plate with -10AN oulets & a place on the top to screw in a factory oil filter...)

So they graciously sent me a replacement adapter to match what was in the photos.

Some 16 days later, I received the correct adapter & got to work fiting everything up...

Until I realised that the cooler core was about 300x300 in size & I couldn't get it to sit in an acceptable place inside my front bar where it would do any good...

Luckily, Just Jap is 15 minutes from my house, so I trotted down to see them & picked up the smallest of their oil coolers, which measured about 90 x 250 & had the -10 nipples that I needed.

'Cool', I hear you say!

Well, yes, everything was cool up until I fitted everything up to the car, with core in place above the intercooler & behind the grille.

Then the leaks started...

Every single one of the yum-cha AN fittings leaked.

That and the braided hose was so soft, it kinked trying to go around a gentle radius bend. :/

Luckily, I have a Pirtek dealer 5 minutes from my house, so I trotted up to see them & came away with two brand new braided hoses featuring -10 Proflow fittings.

'Finally', I hear you say!

So, it turns out I ended up using absolutely nothing from the original package I was sent! :whistling:

So the install was fairly straightforward from then on, with a couple of brackets supporting the core, a 90deg fitting on the nipple closest to the centre of the radiator, running the hose behind the bar reo & a 45deg fitting on the other nipple, angling the hose down past the i/c piping.

The hoses then wrapped around the washer bottle & back into the engine bay through the inner guard liner & met up with the sandwich plate.

Good news: the Proflow fittings don't leak at all! w00t!

Pics:

Brackets

IMG_1933.jpg

IMG_1934.jpg

Fittings & hoses

IMG_2027.jpg

IMG_1935.jpg

IMG_1936.jpg

IMG_2026.jpg

And the finished product

IMG_1931.jpg

The moral of the story:

Don't buy yum-cha oil cooler kits from eBay...

:rant:

Link to comment
https://www.sau.com.au/forums/topic/409089-m35-oil-cooler-adventure/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

So you learnt the hard way, I don't know how many times I've told my mates not to buy those shit china kits!

Just go buy a core and buy the fittings and line from speedflow or who ever you choose, and make the thing yourself.

Your yum cha kit leaks because the fittings are not matched.

They are not hydraulic fittings.

Inside the fittings should be a 45 degree taper

Male and female respectively to couple together and make a mechanical seal.

Look at your relo plates, there is no taper at all.

The oil pressure just forced the oil thru the threads and leaky leaky.

Buy Australian , buy speedflow, don't winge about the money, because as seen here, you end up doing it right the 2nd time.

Good to see you learnt a valuable lesson and also thanks for a detailed post, maybe no guys will think twice before being Jew bags and wasting there money in china on inferior products that clearly will never ever work.

Lol. Good story man. Plenty of times I've been back and forth to pirtek.

Did you have any ability to read before and after results?

I've got an oil temp gauge ready to go on, but the gauge sender ports on the sandwich plate are in a spot that will make the senders interfere with the aircon lines, so I'm waiting on a couple of 45deg 1/8npt elbows that will angle them out of the way.

So no, I can't tell what difference there is now that the oil cooler is on there, but once the gauges are in, I'm planning on bypassing the coolant from the factory sandwich plate & having the new oil cooler doing all the work.

I'll report back once I've got results.

So you learnt the hard way, I don't know how many times I've told my mates not to buy those shit china kits!

Just go buy a core and buy the fittings and line from speedflow or who ever you choose, and make the thing yourself.

Your yum cha kit leaks because the fittings are not matched.

They are not hydraulic fittings.

Inside the fittings should be a 45 degree taper

Male and female respectively to couple together and make a mechanical seal.

Look at your relo plates, there is no taper at all.

The oil pressure just forced the oil thru the threads and leaky leaky.

Buy Australian , buy speedflow, don't winge about the money, because as seen here, you end up doing it right the 2nd time.

Good to see you learnt a valuable lesson and also thanks for a detailed post, maybe no guys will think twice before being Jew bags and wasting there money in china on inferior products that clearly will never ever work.

there was definitely a taper in the yum-cha fittings, but from what i understand now is that the angle of the seats is different... near enough is close enough in China they say. :wacko:

the cheap fittings also felt cheap... they just seemed lighter & less dense than the Proflow ones. In fact I was afraid they'd crack as I was doing them up. :unsure:

lolz.

I bought one a while back......sold it to some tard with a gold POS named Sunkist in Vic! :P

Just an fyi....if your after a good thermo sandwich plate I have a brand new Grex one sitting on my bedside table thats for sale....only issue is it has an R34 adaptor but you should be able to use the one you have just used for you sandwich plate.

Sooooo; did someone say Haydn's awesome Aussie spec oil cooler group buy? :whistling:

Sucks that you had a shite experience; at least you had the good sense not to persevere and potentially damage a motor.

Where is your trans cooler hiding?

Exactly the same spot above the intercooler next to the oil cooler.

It hadn't been fitted in the pictures

There's also a small power steering cooler wedged in just between the oil cooler & headlight now too.

Pay peanuts, you get monkeys. Apologies to Mr 20Valve. LOL

Maybe; but nothing ventured nothing gained. Someone has to take the risk every now & then.

If no-one had tried K-Sport BB Kits, or BC Coilovers they would've been an unrealised performance bargain.

  • 4 weeks later...

Have you had a chance to measure temps yet Hayden?

Considering doing this and trying to work out if the size you've picked is big enough, and if it's not where to fit something bigger :unsure:

To give you a quick idea - cars that I have logged when hot (ie traffic/idle/city driving - NOT giving it a boot) have logged oil temps around the mid to high 90s.

Cheers Alex. I take it that's without a cooler?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...