Jump to content
SAU Community

Internal Gate Screamer

marto184

By marto184,
in Fabrication

 Share

Recommended Posts

marto184 Collaborator

marto184

Posted
Posted

So i'm sitting here wondering if there is a way for me to seperate the dump mouth of a standard 33gtst turbo to make a seperate gate and dump flow.

I have a split dump pipe and i want to know if i can divide the 2 outlets on the back of my turbo into 2 seperate sections, meaning that when my gate opens it goes straight out but when im just cruising it flows along through the full system.

Let me know if anyone has done this before. Im interested in seeing if/how i can do it.

Cheers

Ben

Link to comment
https://www.sau.com.au/forums/topic/410038-internal-gate-screamer/
Share on other sites
reaper1721 Collaborator

reaper1721

Posted
Posted

Most internal gate screamers leak a bit. A piece of metal needs to be added to the turbo side of the exhaust flange to block flow between the waste gate and turbine outlet at the back of the turbo. The trouble with this as far as I am aware is that due to heat expansion, a perfect fit can be problematic. Also, when they are mass produced, differences in casting make it difficult to have a decent seal as one turbo may be 0.5mm smaller than another meaning to seal up on the larger, the smaller would not fit.

Other than that, cut the waste gate pipe off the dump and seal up the hole. The waste gate pipe can then be cut further and routed off to where ever you want it.

Make sense?

  • Like 1
34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

Like a dual port blow off valve type setup? A vent to atmosphere and a plumb back waste gate?

Nope, a screamer is just a pipe that goes atmo from the wastegate... Internals generally don't sound that nice, have issues with leaking (as mentioned) and due to smallish standard turbos would be open a LOT..... I have mates with them but would never do it to my own car.... There is a few different designs around and yes you can do it....

  • 2 months later...
  • 3 months later...
marto184 Collaborator

marto184

Posted
  • Author
Posted

So the stepbrother bought a 32gtst. basically stock with a fmic and 3 inch dump back system. Internal gate screamer fitted and it sounds brilliant. Well worth the cash in my opnion. Although when you see a stock xr6 out accelerate a skyline when the skyline sounds like its got 250rwkw its pretty funny. Not a bad investment guys. If you want that epic gate noise from your car.

34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

So the stepbrother bought a 32gtst. basically stock with a fmic and 3 inch dump back system. Internal gate screamer fitted and it sounds brilliant. Well worth the cash in my opnion. Although when you see a stock xr6 out accelerate a skyline when the skyline sounds like its got 250rwkw its pretty funny. Not a bad investment guys. If you want that epic gate noise from your car.

They sounds average at best, Once you hear a proper external you will know the difference :P

Calsonic14U Mentor

Calsonic14U

Posted
Posted

Looked at one of these for my 32 race car where defect is not a problem. But yes even my race car with only around 200kw would look funny getting smashed by a quieter 33 or something on the track lol.

34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

This haha.

Internal gate screamers sound like ARE an exhaust leak.

FYP

Although all screamers are, it just sounds more degrading that way :P

Alot of people who can't afford the whole external gate setup would like it though. ill see if i can get a vid of it so yous can hear it.

Link Vid!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...