Jump to content
SAU Community

Recommended Posts

My r32 started spullerting as i drive now

It will drive fine then all of a sudden it will glug and then go and glug and then glug a sometimes stall

I have changed

Spark plugs

Fuel filter

Some coil packs as I had spares

Check all hoses

Took off my BOV and put stock back on

Still have it happening

Help! It doesn't seem electrical

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/
Share on other sites

It was happening around the low rev range and was also happening alot when I am on slopes

Havnt driven it much since I have changed everything

I took It for a drive before and went up my street it glugged the whole way up and back down

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/#findComment-6550370
Share on other sites

Only after the problem happened I didn't touch the car before hand

It's funny you say the ignitor

My car stalled and wouldn't start again a while ago and I decided to change the ignitor and it started straight up but was gluggy as it is now

Could that be ignitor as well?

Didn't think about buying a new one

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/#findComment-6554215
Share on other sites

So many things it could be... A few to check/swap/test/clean

CAS

TPS

AFM

Fuel pump

Voltage to fuel pump

Hard to tell as "glug" could mean a lot of things, but if you try all these ^ plus what youve already done you should get somewhere.

Also make sure the spare bits you try are known working, not possibly working. Actually install them on or borrow them from a mates car that runs properly.

Good luck!

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/#findComment-6555717
Share on other sites

Yeah I think it's something electrical

Could it be as simple as my battery?

AFM is fine as far as I know

I clean it every month as I change air filter every month

If its not electrical it has to be the fuel pump

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/#findComment-6556008
Share on other sites

Its most probably the AFM, the contacts inside sometimes come loose and require resoldering. Do a search if you feel confident, or just replace it with a know good one.

Just looking at a component and seeing it is clean doesn't mean it is working.

Link to comment
https://www.sau.com.au/forums/topic/410136-weird-problems/#findComment-6556258
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...