Jump to content
SAU Community

Recommended Posts

Hi guys,

Today i have on offer parts from my er34 gtt.

location of parts central coast , nsw

first up is R/H xenon Headlight

condition - ok mounting tabs good, no bulbs. ( had previous angel eye mod done by old owner, HID cut out when imported.)

price $ 200

willing to ship or pick up

post-57423-0-78864600-1349087714_thumb.jpg

post-57423-0-05519200-1349087784_thumb.jpg

post-57423-0-15755700-1349088146_thumb.jpg

hypergear internal wastegate set for 14psi

Condition - new ( ordered for my old setup as plans have changed no longer need it )

price $ 80 ( thats cheaper then hyper gear)

willing to ship or pick up

post-57423-0-08149500-1349088662_thumb.jpg

bride seat rails - only fit R34

L/H - condition - as new fitted to car for 2 days.

price $ 200

willing to ship or pick up

post-57423-0-13361300-1349088958_thumb.jpg

post-57423-0-25391600-1349089014_thumb.jpg

R/H - condition - used

price $ 90

willing to ship or pick up

post-57423-0-74503600-1349089098_thumb.jpg

post-57423-0-32997800-1349089155_thumb.jpg

stock r34 turbo op6 rear

condition - used appox 150xxx kms on it

price $ 200

willing to ship or pick up

post-57423-0-19864000-1349089237_thumb.jpg

post-57423-0-24539500-1349089309_thumb.jpg

post-57423-0-26416600-1349089391_thumb.jpg

kumho KU31

2 x 225/40/18

condition - used - 50% tread left

cost -$50 per tyre

pick up only

kumho KU31

2 x 235/40/18

condition - used - 20% tread left

cost - $40 per tyre

pick up only

Suntek

2 x 225/40/18

condition - used - 40 to 50% tread left

price - $ 40 per tyre

pick up only

Thanks for reading

contract number is 0437800066 ( MSG or call )

or pm me

If Ryan wants that turbo ill grab it off you and bring it up here bludger, if not there is a guy in the Wanted To Buy section chasing one too!

If Ryan wants that turbo ill grab it off you and bring it up here bludger, if not there is a guy in the Wanted To Buy section chasing one too!

He want highflow,

Come get it then and buy some tyres while you here

He want highflow,

Come get it then and buy some tyres while you here

Ryan thinks your a mongrel :P jks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...