Jump to content
SAU Community

Rb25 Cold Start Valve Clean

HR32GTS 4DOOR

By HR32GTS 4DOOR,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
Posted

So after having problems starting my car without any throttle ever since the engine swap I decided to do something about it.

Also since I couldn't find a tute on here so decided to document the process.

Disclaimer

Attempt this at your own risk. I am neither an auto electrician nor a mechanic. I take no responsibility for any damage that you do to your vehicle in the process of following this guide.

Difficulty - Easy

Time taken 30-45 min

Things you will need

Flat head pliers

10mm socket with 1/2" drive ratchet and extension

phillips head screwdriver

Carby cleaner

A band aid

Directions

The valve on an RB25 is located under the plenum, on an RB20 is is under the throttle body.

locate the valve it is a metal and black thing with two vacuum hoses attached to each end.

This is what it looks like under the plenum with one of the vacuum hoses disconnected.

post-80155-0-55159500-1349257506_thumb.jpg

Use your pliers to remove the clamp and then gently pull the hose off (where it would be in the above picture). The hoses are old and may be quite brittle so take care in removing them.

Then there are two 10mm bolts holding the valve to the bottom of the plenum, use your ratchet and extension to make it a lot easier to access.

after the bolts are out take off the clamp on the other hose and pull the valve from the hose. Again carefully.

Once you have the valve out it should look like this.

post-80155-0-06991300-1349258058_thumb.jpg

there are four screws holding the black plastic part on. undo these and it should look like this. make sure you dont damage the gasket as this will cause a boost leak if not rectified.

post-80155-0-68619800-1349258173_thumb.jpg

I didn't take the valve appart any further as I didn't think it was necessary.

from here spray both parts with carby cleaner, it will probably be all gummed up with oil like mine was so take your time and it should all come up good.

Final result.

post-80155-0-09504000-1349258387_thumb.jpg

Then just do the opposite to put it all back together, also make sure you do up the four screws nice and tight you don't want to have to pull it back off because its leaking.

Link to comment
https://www.sau.com.au/forums/topic/410701-rb25-cold-start-valve-clean/
Share on other sites
  • 1 month later...
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Hey, was your cold start valve plugged in? I've got a RB25 in a R32 that has custom wiring so I'm not sure if there is or isn't a plug for it.

Yeah mine was plugged in. I did the wiring for this engine myself out of an rb20 loom. The plug is a purple/blue plug looks limilar to a side feed injector plug.

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Hey, I found a purple/orange plug underneath the throttle body, so I feed it in between the intake runners and it plugs in to the cold start valve. Will the wiring melt if I leave it like this?

This is how I have mine plugged in, going in between the runners. I haven't had mine melt and I doubt the plenum would get hot enough to do any damage. If it did id say you would have a lot more to worry about.

  • 5 months later...
Tommmay Enthusiast

Tommmay

Posted
Posted

Its under the plenum and above the oil filter. Idle would not really be changed if you didn't have one unless it's just been removed and the vacuum lines were just left there.

Ahhh its there dont know how i missed it

What i meant by that idle comment is when its cold it needs throttle to start/idle after that it seems to idle good

  • Like 1
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Just done my one and it looked brand new inside lol

could the actual mechanism be faulty?

It could be, but its pretty simple so it's not all that likely wiring could be stuffed also. when you start your car for the first time does the idle sit a little higher than when warm like at 1500-2000 rpm? or does it just idle at same rpm as when warm?

Tommmay Enthusiast

Tommmay

Posted
Posted (edited)

It could be, but its pretty simple so it's not all that likely wiring could be stuffed also. when you start your car for the first time does the idle sit a little higher than when warm like at 1500-2000 rpm? or does it just idle at same rpm as when warm?

Pretty sure it idles at the same rpm and will not start without a squirt or 2 of throttle

Sucks cause there is not much information about this issue

Edited by Tommmay
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Ok if it idles at the same rpm there is either something wrong with the valve or it isn't being switched by the ecu (more so a wiring problem) unfortunately I don't know how to test the valve to see if it works. Could check if there is continuity between ecu out and the plug for the valve (will have to look up a pin out diagram for the ecu to find which pin) this will tell you if it is a wiring problem or something else. Could also try another valve, I doubt it would be very expensive from a wrecker

Tommmay Enthusiast

Tommmay

Posted
Posted

Ok if it idles at the same rpm there is either something wrong with the valve or it isn't being switched by the ecu (more so a wiring problem) unfortunately I don't know how to test the valve to see if it works. Could check if there is continuity between ecu out and the plug for the valve (will have to look up a pin out diagram for the ecu to find which pin) this will tell you if it is a wiring problem or something else. Could also try another valve, I doubt it would be very expensive from a wrecker

There is continuity in the plug but who knows how it works without a wiring diagram

Ill just take it in the ass rev it every morning lol

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

I'm not sure but I would assume when you valve is powered (ie when the ecu thinks its cold enough to need it) the valve would be open, so when its appart it would be closed as its not powered. The needing throttle to start can be caused by a few things like vacuum leaks, fuel pump not priming properly etc. If it needs throttle to start when the car is warm then this is not your problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • perry_r33
      Skyline R33 Sedan Tail Lights S2 - (2 SETS Available) Silver & Grey

      By perry_r33 · Posted

      Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...