Jump to content
SAU Community

Recommended Posts

Got my cobb today and am a bit bored at work. Don't have time to take the car to the workshop as it's the weekend but want to try to upgrade the TCM myself to see what the fuss is about in the meantime

I want to upgrade to LC5 and was wondering anyone know which map name and transmission type to select?

Map Name :

* Level 1 - 3300 RPM

* Level 2 - 3700 RPM

* Stock Style LC2 Logic

Transmission Type:

JF04B JF09D JF09E JW91A JW91B JW91D

Link to comment
https://www.sau.com.au/forums/topic/411384-cobb-tcm-question/
Share on other sites

When you go to install the TCM it will tell you which software version you have, then install KB15B (I think thats the code off the top of my head) LC4 VDC OFF V101...or at least thats what we like to use. Its nice :)

Once finished -

Set CC and TP values to zero then perform a Clutch Gear Relearn.

Set CC and TP to desired after that. Start with CC +1, +1, and TP 0, 0

Did the upgrade to LC4 with VDC OFF as recommended by Martin and it is a day and night difference to the LC2. Smoother shifts especially from 1st to 2nd and no more shuddering when taking off slowly or slowing to a near stop and then moving off again. Will play around with LC5 this week to see what the difference (if any is).

Did the upgrade to LC4 with VDC OFF as recommended by Martin and it is a day and night difference to the LC2. Smoother shifts especially from 1st to 2nd and no more shuddering when taking off slowly or slowing to a near stop and then moving off again. Will play around with LC5 this week to see what the difference (if any is).

Hmmmmm The bunny hopping and mild shudder I get in 1st when cold is starting to bug me - as well as reversing the bl00dy thing up a slightly inclined driveway to get out of the garage is doing my head in trying to find the right acc balance point so that I don't launch into the street, or bunny hop or get that clunking clutch slip noise....

What to do what to do... I wanna keep my warranty, but I hate this shit..

CC = Clutch Capacity for Odd and Even gears.

Adjustments range from -7 to +7 and linearly increase clutch apply pressure when shifting.

Normally from the factory these are set to 0 (right in the middle)

On a moderately powered up car setting these to +2 +2 is a good step

In a high powered car then +4 +4 is the go.

I dont go much over that as its hard on the seals and gears to run massive pressures.

Its a feel thing.

TP = Touch Point for Odd and Even gears

Touch Point is best explained as the prepositioning or pre-load on the clutches.

Adding more Odd TP will give more creep in 1st gear at idle speed

I normally leave these as close to 0 as to get the desired driving result

Hope that helps :)

haha how will lc4/5 improve the clutch take up point though?

i'm waiting on my code to upgrade the accessport - can be done through the ap manager now rather than having to send it back to US

i'm hoping the newer launch programs have better control on wheel slip, as 4000k lc will just dry my tyres even more than my current lc3

I was bored and flashed from LC4 to LC5. Maybe it's a psychological thing but I actually like LC4 better for day to day driving. It makes less sound and was a bit smoother during start/stop? I heard LC4 had more slip in the clutch, is this the reason?

I have since reflashed back to LC4 from LC5

When you go to install the TCM it will tell you which software version you have, then install KB15B (I think thats the code off the top of my head) LC4 VDC OFF V101...or at least thats what we like to use. Its nice :)

Once finished -

Set CC and TP values to zero then perform a Clutch Gear Relearn.

Set CC and TP to desired after that. Start with CC +1, +1, and TP 0, 0

Ok. Just followed these instructions precisely. Now I'll take it for a spin and see what the difference is. Still CC at +3 otherwise there is to much slip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...