Jump to content
SAU Community

Recommended Posts

Recently i was getting some squeeling from loose belts on cold startups, so i got under the car and tightened the bolt, unbeknown that it was the wrong one. I later had a look and realised it was the alternator belt that was slipping. So i tightened the belt tensioner bolt on the alternator.. Squeeling fixed.

But, the bolt under the car, for the big belt.. not sure what it runs, is fairly tight.

How tight is too tight? I can push the belt a few mm, but other than that its very tight.

I tried undoing the bolt, which is how you loosen the belt, but it just screws out without moving the adjustor wheel.

Link to comment
https://www.sau.com.au/forums/topic/41198-fan-belt-tightness/
Share on other sites

Its part of the alternator you cant miss it, just look and youll see it, the bolt is facing the body of the car not the engine. Its attached to a metal slide kind of thing so when you tighten or loosen the bolt... it pulls/pushes the alternator towards or away from the engine hence tightening the belt

Recently i was getting some squeeling from loose belts on cold startups, so i got under the car and tightened the bolt, unbeknown that it was the wrong one. I later had a look and realised it was the alternator belt that was slipping. So i tightened the belt tensioner bolt on the alternator.. Squeeling fixed.

But, the bolt under the car, for the big belt.. not sure what it runs, is fairly tight.  

How tight is too tight? I can push the belt a few mm, but other than that its very tight.

I tried undoing the bolt, which is how you loosen the belt, but it just screws out without moving the adjustor wheel.

tighten the belt until you have 5-7mm deflection on its longest run between pulleys

Sumo: YOU are right. the only thing is that I CANNOT undo that bolt!!! it's so farken hard stuck in!!! that bolt is screwed in from the rear of car to front of car, so to undo it you go anticlockwise from the rear looking to the front, i am lifting the spanner instead of pusing down! right? it will not budge!

  • 1 month later...
  • 1 year later...
Recently i was getting some squeeling from loose belts on cold startups, so i got under the car and tightened the bolt, unbeknown that it was the wrong one. I later had a look and realised it was the alternator belt that was slipping. So i tightened the belt tensioner bolt on the alternator.. Squeeling fixed.

But, the bolt under the car, for the big belt.. not sure what it runs, is fairly tight.

How tight is too tight? I can push the belt a few mm, but other than that its very tight.

I tried undoing the bolt, which is how you loosen the belt, but it just screws out without moving the adjustor wheel.

hello,there

I am sorry that I don't know any mechanical stuff but i am having squeeling noises from what i suspect to be the fan belts. This is because this happened as soon as I had the fan belts changed last week.

can anyone kindly post photos or diagrams of where the related bolts are to be tightened? thank you,everyone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...