Jump to content
SAU Community

Turn Signal Fuse Keeps Blowing Up And Indicators Stop Working

nnt

By nnt,
in General Maintenance

 Share

Recommended Posts

nnt Rookie

nnt

Posted
Posted

Hey guys!

Just the other day driving home I indicated in to a servo and after one click it just died. I checked the fuse box and found the turn signal fuse blew up, same with the hazard one. Got them both changed and after driving around a few corners it blows up again. Changed the combo switch (stalk), put in new fuses, still blew them all up. It also killed my alarm as its connected to blinkers, but its now disconnected from the blinkers so it works like normal now. So im wondering if anyone know what the problem could be? As its strong enough to kill my alarm, I doubt it could be the flasher relay?

And ive also noticed I got a electronic flasher can, this is from the previous owner. I think the reason why he put it there is because I got the front blinkers hooked on to the parkers as its an aftermarket front bar, so the front blinkers sit at the corner of the headlight using parkers which shouldnt be the cause? Been driving around for ages without this happening, just recently happen out of nowhere.

Thanks for the help in advance guys! :worship:

nnt Rookie

nnt

Posted
  • Author
Posted

Nope nothing to do with rain actually, been quite sunny. What im going to do is change electronic flasher can for now, hope that helps. but just wanted to see if any1 know what else could be problem to see what is wrong.

nnt Rookie

nnt

Posted
  • Author
Posted

I doubt it is the alarm system, I have disconnected my alarm relating to the blinkers now, and the fuses still keeps going, thats why i reckon its not the alarm thats causing the short. Totally forgot about the wiring loom above my wheels, gotta check it out, thanks mate!

Moodles2 Grand Master

Moodles2

Posted
Posted

Turn signals lights usually use a single element 1156 bulb, brake/tail lights and sometimes turn signals use 1157 bulbs (dual filament 5w/21w etc). The only difference between the 2 is obviously the single/dual filament and the placement of the prongs. Someone might have put a 1157 bulb where a 1156 was needed or vice versa. I know it's possible to force either into the opposing socket, and wierd things can happen. I've done this myself on my motorbike's tail light.

To tell the difference between bulbs: http://autorepair.about.com/od/electricalrelateddiyjobs/l/aa010502b.htm

ZacZerbst Enthusiast

ZacZerbst

Posted
Posted

re the front indicator globes 21w? If not that will be the reason for the electronic flasher unit. They are generally fitted when led lights are installed. Fitting a standard flasher unit will result in a fasy flash rate. Have you inspected the flasher unit as i have seen them short internally. The other thing would be to try your hazard light and see if that causes the fuse to blow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...