Jump to content
SAU Community

Recommended Posts

Mark has copped to the harsh reality regarding his ability to eek out life from the Pirelli tyres "...but that's the way it's been the last... since 2011. I'm not going to learn now, mate. Old dog, new tricks, it's over."

:(

Formula 1's 2014 calendar is set for a major reshuffle when it is firmed up next month, with New Jersey and Mexico likely to be dropped.




Kimi Raikkonen has reached a provisional agreement with Lotus to settle his pay dispute, AUTOSPORT can reveal, which should ensure he completes the 2013 Formula 1 season with the team.



good news!

Lotus's long-term Formula 1 future received a major boost on Sunday night when investment group Quantum Motorsports said its deal to buy into the team was complete.
Mansoor Ijaz, who is the head of the Quantum Motorsports consortium that includes Middle East investors, said that his company had now completed its side of the contract and just needed final approval from team owner Genii Capital.
"There is no question that the deal is definitely happening," he said, when asked by AUTOSPORT about the latest situation.
"I will even go out as far as to say that it has now been completed from our side in terms of what has to be done."
Quantum plans to buy a 35 per cent stake in the team through new shares issued by majority owner Genii.
There are also options for it to potentially take over the entire running of the team in the future, should Genii wish to scale down its involvement.
"We have options - I won't go into the details of those options - but the options do allow us in a fixed amount of time to take control of the team later on," Ijaz added. "We will do that in a way that is very co-ordinated with our partners at Genii."

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...