Jump to content
SAU Community

Recommended Posts

I sold my car and there are some spare parts left.

Pick up price.

- standard clutch and pressure plate (fairly good condition) $40

- standard M-spec front bar (white). I cut the middle part of the bar off to get better air flow to the FMIC. not a very clean job but little bit of work can make it nice. Sale for $40 SOLD

- Standard gear nob (abit worn) $10 SOLD

- Standard intercooler with pipes very good condition $60

- Standard dump pipe and Cat. $20 SOLD

- Spitfire boost gauge read up to 20psi. only used for 3 months. Bought for $130. sell for $60

- Turbo smart boost controller. bought for $100 bux only used for 3 months. Sell $40[/color] Lost, No longer for sale

- 3 Goodyear Eagle F1 tyres 215/40/17 50% tread left. 3 for $30

- Standard boost controller. $10

- stanless exhaust tip ( not sure if its 2.5 or 3 inch) . very good condition $80

- Philips Tape and Radio player. $20

- A few Neon Lights & etc.... $15-30

call 0414228278

thanx

Link to comment
https://www.sau.com.au/forums/topic/41504-fs-cheap-r33-gtst-parts-sydney/
Share on other sites

I sold my car and there are some spare parts left.  

Pick up price.

-  standard clutch and pressure plate (fairly good condition)  $40

-  standard M-spec front bar (white). I cut the middle part of the bar off to get better air flow to the FMIC. not a very clean job but little bit of work can make it nice.  Sale for $40

-  Standard gear nob (abit worn) $10

-  Standard intercooler with pipes very good condition $60

-  Standard dump pipe and Cat. $20

-  Spitfire boost gauge read up to 20psi. only used for 3 months. Bought for $130. sell for $60

I sms you and pm you but no repoly for the boost gauge. I am not sure what they look like. Do youhave a pic? Or a link I could look at.

Johnathon

-  Turbo smart boost controller. bought for $100 bux only used for 3 months. Sell $40

-  3 Goodyear Eagle F1 tyres 215/40/17  50% tread left.  3 for $30

Or have everything listed above for $250

call 0414228278

thanx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...