Jump to content
SAU Community

Recommended Posts

So on saturday, i fitted some new injectors. 550cc.

Its running super rich and constantly stalls so i guess i just need to get it tuned?

I was told it would run fine with this size injector, but i guess he was wrong?

Just wanted to double check that its probably just the tune, because on saturday, i did about 60km after fitment, ran like a dream, no worries at all. But today, running like a dog.

Cheers in advance for any help.

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/
Share on other sites

Sounds as though it's already been somewhat tuned to suit.

You upgraded from stock injectors? If so there's no way it would of run ok without any tuning. Someone on here tested theirs on idle got overconfident and was lucky to limp the car home after going around the block far too much fuel

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662126
Share on other sites

So on saturday, i fitted some new injectors. 550cc.

Its running super rich and constantly stalls so i guess i just need to get it tuned?

I was told it would run fine with this size injector, but i guess he was wrong?

Just wanted to double check that its probably just the tune, because on saturday, i did about 60km after fitment, ran like a dream, no worries at all. But today, running like a dog.

Cheers in advance for any help.

is it using a power fc or stock ?

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662143
Share on other sites

It will be sitting in the drive way until i get it tuned, which ive just organised, so im not that worried.

Stock injectors dirt cheap would be second hand, yes? Id rather put new stuff in. Nothing a little money wont fix =D

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...