Jump to content
SAU Community

New Injectors

Spence_R32

By Spence_R32,
in Engines & Forced Induction

 Share

Recommended Posts

Spence_R32 Enthusiast

Spence_R32

Posted
Posted

So on saturday, i fitted some new injectors. 550cc.

Its running super rich and constantly stalls so i guess i just need to get it tuned?

I was told it would run fine with this size injector, but i guess he was wrong?

Just wanted to double check that its probably just the tune, because on saturday, i did about 60km after fitment, ran like a dream, no worries at all. But today, running like a dog.

Cheers in advance for any help.

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/
Share on other sites
Marcus89 Proficient

Marcus89

Posted
Posted

Sounds as though it's already been somewhat tuned to suit.

You upgraded from stock injectors? If so there's no way it would of run ok without any tuning. Someone on here tested theirs on idle got overconfident and was lucky to limp the car home after going around the block far too much fuel

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662126
Share on other sites
AngryRB Grand Master

AngryRB

Posted
Posted

So on saturday, i fitted some new injectors. 550cc.

Its running super rich and constantly stalls so i guess i just need to get it tuned?

I was told it would run fine with this size injector, but i guess he was wrong?

Just wanted to double check that its probably just the tune, because on saturday, i did about 60km after fitment, ran like a dream, no worries at all. But today, running like a dog.

Cheers in advance for any help.

is it using a power fc or stock ?

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662143
Share on other sites
Spence_R32 Enthusiast

Spence_R32

Posted
  • Author
Posted

It will be sitting in the drive way until i get it tuned, which ive just organised, so im not that worried.

Stock injectors dirt cheap would be second hand, yes? Id rather put new stuff in. Nothing a little money wont fix =D

Link to comment
https://www.sau.com.au/forums/topic/415323-new-injectors/#findComment-6662218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...