Jump to content
SAU Community

Recommended Posts

what did you use to re-seal. I may have done the same thing. What does it do? or just use more fuel? I wiped mine down not scrubbed it, so was it a hard sealent??

It seals the throttle body and stops it from being a vac leak.

My idle has been screwed ever since I did it haha.

It's just like a thick grease like substance, that's why I mistook it for blowbye.

In robs first pic the top boost line has been cut and clamped and the black wire has already been earthed. But I haven't seen it hit 6psi

Do you have an aftermarket boost gauge or only the stock one in the cluster?

Stock doesn't read in psi.

not sure with 33s but it should be 650 to 850. but it also depends with the temperature of the engine if it cold it will idle higher as the 02 sensor is still working on calculating the fuel mixture. If its warmed up to a certain temp then the rpm drops. or you have your AC on or heater. Or even a hetkik sub will drop your revs when pounding

theres also parallax error that could actually be a 900rpm but the way you took the pic make it look like just below 1000 lol

Intake Air temp sensor its one of the things my ECU needs if it gets too hot it reduces timing.

ohh its one of the things i did today tested out my tig skills from Tafe and still not too bad left a hole at the start

post-77241-0-03591600-1384865748_thumb.jpg

post-77241-0-57060000-1384865805_thumb.jpg

Yea. That was warm and the sub wasnt going hard enough to drop the volts. Also the timing belt wines really bad :/ don't know what that's about but I'm not liking it !

Intake Air temp sensor its one of the things my ECU needs if it gets too hot it reduces timing.

ohh its one of the things i did today tested out my tig skills from Tafe and still not too bad left a hole at the start

Oh ok. Thought it may have been something like that. Would be interesting to have a gauge/readout on that too.

Yea. That was warm and the sub wasnt going hard enough to drop the volts. Also the timing belt wines really bad :/ don't know what that's about but I'm not liking it !

Timing belt could need replacing or if it's a "Gates Racing" belt they are noisey. Mine was.

And Bryce that welding isn't to bad !! Here's my go at it haha

post-127489-0-55948400-1384866227_thumb.jpg

The outside is a lot better. Just filled in some gaps so it didn't leak

Edited by ..::R33GTS-T::..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...