Jump to content
SAU Community

Recommended Posts

yea, someone spotted a black 33 on the side of the parkway, I figured it would have been you.. not to many black 33 with chromies on... sorry to hear that man :(

Finally gearbox is in and everything bolted back to where it was. It was late so couldn't take it for a test drive. Big thanks to 5hiv and Eiji for helping out.

Thats what we are here for help each other out :)

now i need to fix mine slowly

SkyWagon Rego Re-inspect PASSED! :banana: (cost $14.40 for a guy to walk out, shine a torch thru a rear wheel and say yep) :blink:

Also Wheel alignment done. Toe out was way out on both sides. More than 2mm on drivers side and nearly 5mm on passengers side.

Belco Jane Bob.

  • Like 1

jacked the car up, about to drop the oil out, just making sure is Castrol edge titanium 0w-40 full synthetic all good to go in the 33? have a bottle left over form an oil chance on the fpv a couple of months ago

I wont be driving it to often, timing belt needs to be retention, will it be ok ? I have no idea when the last oil change was, it has a Japanese oil filter in it (imported in 05)

from everyone's comments its way to thin yea?

Edited by ..::R33GTS-T::..

I use... Ryco Z145A Oil Filter and Nulon 10w40 Synthetic oil. Nulon 20w50 in the Wags cooz it's old...

some say to go higher for Hot weather and Track. (as in 50 or 60)

yea I just got the z145a oil filter, I literally had the spanner on the sump plug, then thought I would double check... the only real how wether driving ill be doing in this sat... and no track days till I get my ps, it will be up for an oil change by then..

Nissan recommends 7.5w 30/40. Use 5w 40 or 10w 40, if its a shittier oil 10w 40, but if its like Motul etc you can probably get away with 5W 40. You need to examine your engine and see how much wear you have.Not all engines are the same. Check your compression and how much blow by you have to see what thickness of oil you should run. More blow by means your oil is too thin for your worn piston rings you will also get a lower compression reading. i use 10w 40 summer 5w 30 winter.

Started fixing my car and found out that the air con belt was smoking and i think the air con compressor is seized thats why when the engine tries to turn the compressor it smokes.

Edited by 5hiv

Have to change my fuel pump on the 33 me thinks..
Car seems to be chugging a lot and missfires these days.
Had a look over my notes and I haven't ever changed the fuel filter (last change was by dvs jez when the car was tuned)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...