Jump to content
SAU Community

Sau A.c.t. - What Did You Do To Your Car Today?

Got a Pulsar

By Got a Pulsar,
in Australian Capital Territory

 Share

Recommended Posts

  • Replies 5.2k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

GTRKat
GTRKat

Looked at pictures of it but happy to know there is progress!!!

RosieR34
RosieR34

Just got Rosie back from John at Trojan. 35kw gain and cheerin', so responsive now. 10k service brake pads SAFCII install and tune. 200kw - 200 club!

dontyellpl0x
dontyellpl0x

Got myself a new toy! Time to build a race car!

Posted Images

..::R33GTS-T::.. Proficient

..::R33GTS-T::..

Posted
Posted

it was when I first got the car, wasn't running! the radiator was snapped in half

I also had to do the lower control arm in mine when I got it, they are a bitch!!

and rob, my rpm stops every now and again, any ideas? my mates 33 did the same thing

Got a Pulsar Grand Master

Got a Pulsar

Posted
  • Author
Posted

Somewhere between the engine and your eyeballs. :P

I'd try checking for loose wires / dodgy earthing. Could be in behind the cluster etc...

Not hard to pull out.

(once you've done it a few times) lol

  • Like 1
D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

Fibreglassing repairs today, all done.

The instructions say mix a certain amount so you can get it on before it hardens.

DIY Miks painting skills mean i can mix the whole tin and get it on good, well before it starts to harden. job done. :thumbsup:

I was feeling so good until i remembered... the only way to get fibreglass off is a cold shower. :O:blink:

  • Like 1
..::R33GTS-T::.. Proficient

..::R33GTS-T::..

Posted
Posted (edited)

Fibreglassing repairs today, all done.

The instructions say mix a certain amount so you can get it on before it hardens.

DIY Miks painting skills mean i can mix the whole tin and get it on good, well before it starts to harden. job done. :thumbsup:

I was feeling so good until i remembered... the only way to get fibreglass off is a cold shower. :O:blink:

I found that out when helping dad fiberglass his sub box in the old f6 typhoon... not very nice!

Somewhere between the engine and your eyeballs. :P

I'd try checking for loose wires / dodgy earthing. Could be in behind the cluster etc...

Not hard to pull out.

(once you've done it a few times) lol

hahahaha!!!! smartass!!

yea I have pulled the cluster out already, couldn't find any loos wires, will look for the earth wires on the weekend :)

Edited by ..::R33GTS-T::..
Sinista32 Grand Master

Sinista32

Posted
Posted

Strongly recommend not letting your Skylines get so low on fuel that the fuel light comes on.

+1

I don't allow my GTR get below a qtr of a tank.

Listen or learn.

But just don't breeze over good advice, especially if you have modified your car.

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

got no mods, well no power mods, and I still don't let it go under a quarter

I have never had my fuel light on, and the gauge has been like 3mm under the empty line... and I sure as hell don't want to see if the bulb is broken

Make up your mind

D.I.Y. Mik Veteran

D.I.Y. Mik

Posted
Posted

I just made sure the intake is the same height as stock, and while i was there i could see how it gets the last bit of fuel.

Kinda dodgy baffles try to keep it near the pump, but a good corner or steep hill and it would run away and youd get air in the line.

After pulling it out and f-ing around trying to re-seal it, i still smell fuel inside the car sometimes. Have to do it again better this time. DIY LOL :huh:

..::R33GTS-T::.. Proficient

..::R33GTS-T::..

Posted
Posted

Make up your mind

haha, it was heaps under when I got the car, didn't drive it, got a jerry can... im talking about I wont let it under while driving :P

but good spotting :/

dontyellpl0x Mentor

dontyellpl0x

Posted
Posted (edited)

As I said I've seen my fuel light come on once in 10 months. I normally fill up when it hits E, but my sender is not correct and I can only fit in 40-45 litres

Edited by dontyellpl0x
Sinista32 Grand Master

Sinista32

Posted
Posted (edited)

It's like fuel cut.

It can do engines in if it occurs at the wrong time

Bit dramatic I know, but it happens.

(your better of stopping spark than stopping fuel)

Edited by Sinista32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • GTSBoy
      Valve clearance for RB25det series 2

      By GTSBoy · Posted

      This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Kinkstaah
      Valve clearance for RB25det series 2

      By Kinkstaah · Posted

      Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...