Jump to content
SAU Community

Recommended Posts

Got some bits in the E-go Courier Post today. :) Gotta love Gumtree.

Extractors , Grill and ECU sent from Melbourne.

post-78856-0-73209600-1413972359_thumb.jpg

Supposedly the Extractors are Genuine SVD pipes, Grill is series1 or SSS? and ECU has apparently been Chipped to suit cam and port n polish.

Price was hard to resist. :D

Ordered surge tank+fittings for the cressida, some adjustable upper controls arms for the racecar and headstuds for the other gtr. Also ordered water and iac hoses for a patrol im doing a motor conversion on. Annnnnd im out of money again :/

Ordered surge tank+fittings for the cressida, some adjustable upper controls arms for the racecar and headstuds for the other gtr. Also ordered water and iac hoses for a patrol im doing a motor conversion on. Annnnnd im out of money again :/

Know your feel bro.

About to spend a solid amount @ Ultimate

Tried everything I could think of to get the broken exhaust stud out of the head but couldn't get it so I just slapped 7 new studs in, new gasket and put the SVD extractors on.

post-78856-0-46410300-1414324886_thumb.jpg

Old gasket was well past it's use by.

post-78856-0-42845800-1414324760_thumb.jpg

Recently made a shield for the pod filter too. TUPPERWARE!!! still has a label on it that says "popcorn" :laugh:

post-78856-0-43503800-1414324773_thumb.jpg post-78856-0-01958400-1414324868_thumb.jpg

also got a new pair of Driveshaft seals from Nissan.

Rang to order them as I was previously told by Nissan that they would have to be made in Japan and sent over. (3 - 4 weeks) and would cost $28.?? each.

Got them sent from W..A. in 2 days for $55 the pair. :D

Will get around to putting them in sometime...

Tried everything I could think of to get the broken exhaust stud out of the head but couldn't get it so I just slapped 7 new studs in, new gasket and put the SVD extractors on.

attachicon.gifN13 Exhaust Gaskets.JPG

Old gasket was well past it's use by.

attachicon.gifSkyHatch Extractors 2.JPG

Recently made a shield for the pod filter too. TUPPERWARE!!! still has a label on it that says "popcorn" :laugh:

attachicon.gifSkyHatch Post Extractors 1.JPG attachicon.gifSkyHatch Post Extractors 2.JPG

also got a new pair of Driveshaft seals from Nissan.

Rang to order them as I was previously told by Nissan that they would have to be made in Japan and sent over. (3 - 4 weeks) and would cost $28.?? each.

Got them sent from W..A. in 2 days for $55 the pair. :D

Will get around to putting them in sometime...

Wow that's probably the only Pod Box that has a lifetime warranty

Rob. Worthwhile finding a cover for the relays near the wiper bottle. Bit exposed.

Not sure if the fuseable links are meant to be covered or not.

The 31 is the same.

Not sure if the Tupperware warranty would apply as it's been cut. :/

Not sure if the fuseable links are meant to be covered or not.

The 31 is the same.

Not sure if the Tupperware warranty would apply as it's been cut. :/

LIFE TIME WARRANTY.

You dropped it and it poped a hole in it....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...