Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • Replies 87
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...
  • 1 month later...

Cusco tension rod brace, accralite forgies, head, charcoal canister and HKS exhaust gaskets all SOLD!!

Just a bit of an update on what I have left:

Pair of standard R32 GTR turbos in good condition $300
Pair of T517z turbos, one probably needs a seal kit as it was a bit smokey, otherwise still ran well SOLD
R32 GTR 3" exhaust (unknown brand), also comes with 3" straight through pipe and v band style clamp for a quick swap out from quiet to loud in 5 mins SOLD
R32 GTR front pipe, 2.5 - 3" (unknown brand) SOLD
R32 GTR standard manifolds $50 each
R32 GTR manifold heat sheilds $20 each
Nismo 555cc injectors, good condition SOLD
R32 GTR fuel rail and reg (standard)
SOLD
R32 GTR fuel rail $50
Nismo fuel reg SOLD
Tomei Sump baffle SOLD
RB26 86.5mm Accralite forged pistons (used), good condition, comes with a set of standard rods (will not separate)
SOLD
RB26 twin turbo pipe $100
RB26 head (standard), NO COVERS OR CAMS , slight indentation on no6, will need a refresh as its been sitting for a while
SOLD

RB26 intake manifold with itb's and sandwich plate SOLD

Used standard coil packs $100

Used splitfire coilpacks $350
Apexi pods with afm adaptors and brackets SOLD
R32 GTR afm's (one was opened to fix a solder joint, works perfectly fine) SOLD
R32 GTR Cusco tension rod brace
SOLD
R32 GTR front sway bar (standard) $100
HKS metal exhaust manifold gaskets, good condition
SOLD
R32 GTR charcoal canister SOLD
RB26 various intake pipes (standard) from $10
R32 GTR air con ducting (everything from under the dash to under the carpet, bar i piece that goes to driver side round vent) $50
Will post at buyers expense, or pick up near Wollongong NSW.
All items are "or nearest off"
If you want pics, please inbox me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...