Jump to content
SAU Community

Recommended Posts

Hi everyone, my name is Kiley and I'm actually on here from the USA. I don't have a Skyline because well, they're not legal here. So I did the next best thing and bought what we call a 240sx (not sure if they call them that there or not) and installed a RB26 out of an R33 skyline GT-R. So I got that going for me.

What's my reasoning for joining your site then you may ask? I've been wanting to go single turbo on my RB26 and need to sell my current twin turbo setup. I've tried on my continent but hope I can find some interest on yours too!

I'll post some pictures of it and a link to my build thread on one of the American forums so you can tell I'm a real person. But here's some basics of the car. Look for the stuff for sale in the "parts for sale" section soon. Thanks!

How the car looked when I first got it:

000_0034.jpg

A couple tables of parts for the motor:

IMG_0333.jpg

100_0202.jpg

18x12 inch SSR Professor SP3's for the wheels:

7.jpg

All back together and ready to go in the car:

top.jpg

Getting the car tuned:

beforedynoedited.jpg

460whp (not sure what that equals in your terms!) on 93 octane pump gas.

Nearly didnt fit with the BN Blister widebody kit:

100_0382.jpg

First test drive!

DiffBreakInclosefront.jpg

So again thanks for checking it out. I'm honored to be on a site with so many very nice, very real skylines.

Link to comment
https://www.sau.com.au/forums/topic/418941-new-from-the-united-states/
Share on other sites

that is shit hot.

and i bet it cost you f**k all cos you live in maryker.

god damn that would be so illegal in victoria! all the best man, and more pictures/videos. get that on proper fuel and retune it.

Ah and as I said here is my build thread:

http://forums.nicoclub.com/beat92-s-overkill-is-underated-build-thread-t518849.html

Here's a video for anyone interested in hear HKS272 cams on an RB26 at idle. One of my favorite short videos of the car:

And here's a video from the guy that tuned it. Shows the Haltec Racepack dash I have as well as a dyno sheet at the end:

Thanks for the good words! It was a very expensive build here since no parts are available. I actually got a lot from Australia because they seem pretty common there.

I would have thought your laws would be easier on cars since you can actually have skylines there. You have so many cars I wish I could get here.

Thanks for the good words! It was a very expensive build here since no parts are available. I actually got a lot from Australia because they seem pretty common there.

I would have thought your laws would be easier on cars since you can actually have skylines there. You have so many cars I wish I could get here.

wow brother! australian prices must have scared the shit out of you!

im not too sure on laws for standard cars. but in the state of victoria the police do not look kindly upon modified cars!

im pretty sure if they saw yours on the road they would just shoot you on the spot. :woot:

all the best with the sale and stuff man......

Pricing was better in Australia then in the US! Shipping was just more expensive than usual, but not unreasonable.

Hardest thing was finding factory parts like valve spring shims for adjusting them. We couldn't find any and didnt want to risk not being able to find any in future valve adjustments so we got Kawasaki street bike valve shims and machined my valve retainers to accept them for spacing. Little extra work but Kawasaki bike shims are a lot easier to get than RB26 ones here!

Other than that it was a lot of fun and certainly worth it for something very rare around here.

Our police don't take kindly to it either due to it being straight pipe exhaust....but I'll keep my bullet proof vest on if I ever come to AU then!

dont liten to this guy. hes put a 30 year old v8 in his r33.

My V8s newer then your cast block 6 ya smeg head lol

Plus i said I liked the car :/

Edited by Captain Natro

looks farken hawt!

welcome.

also, its a 240sx over there, but the combo of that front and that rear wasnt available here or japan from factory.

the front is from a 180sx.

the rear(shell) is an s13 silvia.

and yes, alot of the mods youve made, couldnt even get close to legal over here.

but trust me when i say, if we could, we would.

and are NO skylines legal?

i thought it was just the gtr's?

hope you enjoy our site.

if you ever come to aus, come to one of our runs and have a chat.

we're all pretty friendly people.

looks farken hawt!

welcome.

also, its a 240sx over there, but the combo of that front and that rear wasnt available here or japan from factory.

the front is from a 180sx.

the rear(shell) is an s13 silvia.

and yes, alot of the mods youve made, couldnt even get close to legal over here.

but trust me when i say, if we could, we would.

and are NO skylines legal?

i thought it was just the gtr's?

hope you enjoy our site.

if you ever come to aus, come to one of our runs and have a chat.

we're all pretty friendly people.

Good to hear you guys appear to be having fun on this forum. They've kind of died over here because everyone's to serious!

Everyone here always tries to put the "JDM Silvia" front end on my body style, but I'm a fan of the flip ups for some reason. Like you said it was never offered anywhere else as far as I've found so it seemed different world wide even though its not different here.

I thought from all the RB parts I've found from there that it was pretty much anything goes over there! You've crushed my dreams by telling me you apparently have a stricter government then we do.

As for no Skylines being legal, none are to be brought straight over. Something like 96-98 R33 gtr's are but you have to do a lengthy and expensive legalization process like changing the car to OBDII and some emissions system work. But 96-98 GTR's are the only ones that were ever crash tested. You can get any as track cars but none legal to drive on the road yet. We have a 25 year "classic car" rule so we can start bringing in R32's next year under that. Canada only has a 15 year so they've been bringing them in for a while now up north.

And if I ever come over there it would be one of my goals now to meet up with a skyline meet. I'll keep it in mind thanks!

Awesome build all the shiny new parts on the bench are what wet dreams are made of! :woot:

Welcome to SAU this is the best site for RB tech lotsa the guys here REALLY know their shit :thumbsup:

I actually came here a lot during the build. Most info I could find on the RB that was in English and I could mostly understand.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...