Jump to content
SAU Community

Recommended Posts

So recently i removed my lenses and sprayed the chrome surrounding in the headlights black, and after doing that my headlights fog up with any sight of moisture which is really annoying. I knew it was a possibility to happen but i took the risk anyway. So now i want to remove the outside lense completely like this. Anybody done it?

post-106657-0-97455100-1361740286_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/420538-lensless-headlights-diy/
Share on other sites

If you took your lenses off then you know that the headlights aren't sealed. You wouldn't want to drive in the rain with them exposed. So, to do the lensless conversion correctly you'd need to convert to sealed headlamps. That's a pretty big deal as you'd have to totally change out the mounts and adjustment stuff.

Not saying impossible, but it would be a fair bit of work.

I have a banked up project to convert mine to projectors (can't justify the Series 3 expense) and I want to change a few other things when I'm in there. I'll eventually put up a thread when done, but prob won't be till next year.

Pretty hard to see in that picture. Might just be converted to slim rectangular sealed units. Lot of 80's and 90's cars used them before custom lenses with replacement bulbs became the norm.

The R32 Autostyle car had ones like this but they looked like sealed projectors.

1916_12mg.jpg

Read up on it. Search here on the forums, there is a DIY.

I removed mine to fix a broken adjustment bracket. Use a heat gun or oven to soften the glue then you have to work around it with screw drivers carefully not to crack the plastic.

Don't personally like that style I prefer two square lamps. Each to their own though. Im gonna try get hold of a dremel with a circular attachment or even one of those renovator tools and try cut out the outter lense along the little dip around the diameter of it. I will take pictures as I go and keep you updated. Fingers crossed it turns out reasonable haha!

Yeah obviously you'd get the RWC issues but hey, people run spacers, decats, high mounts, ffp's etc ;)

Yeah, I guess you have a point but...this mod will stick out like a sore thumb screaming for unwanted attention!

Yeah, I guess you have a point but...this mod will stick out like a sore thumb screaming for unwanted attention!

Definitely agree! On a noobish note, are R33 GTST series 1 and 2 headlights interchangeable/line up fine? On my phone so the search option isn't the best.

  • 10 months later...

If you took your lenses off then you know that the headlights aren't sealed. You wouldn't want to drive in the rain with them exposed. So, to do the lensless conversion correctly you'd need to convert to sealed headlamps. That's a pretty big deal as you'd have to totally change out the mounts and adjustment stuff.

Not saying impossible, but it would be a fair bit of work.

I have a banked up project to convert mine to projectors (can't justify the Series 3 expense) and I want to change a few other things when I'm in there. I'll eventually put up a thread when done, but prob won't be till next year.

So thread resurrection. Not really finished yet but I've had this project and doing a little here and there over the last year when I have the spare time. I've also got an motor rebuild happening so this is going to take a back seat for a few weeks since the parts are starting to come back in.

This is quite different from anything I've seen on R33's. I also have modified the grill to come out almost to the front of the bumper. The "eye lid" will extend the bonnet line. I will be finishing in fibreglass and then doing carbon overlay over the top.

IMG_2257.JPG

IMG_2263.JPG

IMG_2264.JPG

  • 2 weeks later...
  • 9 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...