Jump to content
SAU Community

Recommended Posts

have you ever been through the mallaca straights?

it really is amazing it doesnt happen more often. its not like the ships can just put on the brakes and stop in 100m.

I was heading into singapore once (sailed in there a few times), and at 45 degrees to port and starboard or the bow, I counted over 90 contacts, then I gave up.

Link to comment
https://www.sau.com.au/forums/topic/42054-ship-sinks/#findComment-861509
Share on other sites

How the *** do you colide with a supertanker?  

Its not like u wouldnt see it coming!

Surprisingly its fairly easy for larger ships to collide.

Problem is that they are very hard to manouvre. You just cant turn them around or stop, it can take a long distance (kilometres)

Often they come across each others path's at fairly late notice and in heavy seas, or fog its all over. In really heavy seas its possible to loose sight of big ships very easily.

Commercial ships are alot different to control than a small tinny or even a 60ft charter boat!

Link to comment
https://www.sau.com.au/forums/topic/42054-ship-sinks/#findComment-861520
Share on other sites

that actually happened last week..and it was only about 100 japanese second-hand cars..still a shame though.

I had a friend last week whose car managed to make it safely to Australian shores, only to have a container accidentally dropped on it. doh!

Link to comment
https://www.sau.com.au/forums/topic/42054-ship-sinks/#findComment-861718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...