Jump to content
SAU Community

S A U - N S W Tech Night For Members 24Th Apr - Engine Builds


Recommended Posts

Beware of wastelanders :P

...you mean you'd have the temerity to turn megzz into one?

Hehe...

I predict that megzz might turn up to our AGM. No wastelanders there - not

  • Replies 195
  • Created
  • Last Reply

Top Posters In This Topic

...you mean you'd have the temerity to turn megzz into one?

Hehe...

I predict that megzz might turn up to our AGM. No wastelanders there - not

no, none there :whistle:

I am guessing all spots are filled out? Nooo! :(

Can you organise your Membership Application & Payment please Raj?

Even whilst you're vying for the reserve list, the next Tech Night in July will be Members Only as well.

Kind Regards, Tez

Can you organise your Membership Application & Payment please Raj?

Even whilst you're vying for the reserve list, the next Tech Night in July will be Members Only as well.

Kind Regards, Tez

Thanks Tez. I have PM'd "Shell" regarding the membership application.

Fingers crossed for this event! Will surely be in-line for the July one :)

All is good, I had forgotten I had booked to go to Eastern Creek drags for the first time!! Hopefully won't blow anything..

That's OK Luca. Hope things are fine with you!

Post #1 updating.

All is good, I had forgotten I had booked to go to Eastern Creek drags for the first time!! Hopefully won't blow anything..

If you do then tow it to JEM and they can fix it :P

If you do then tow it to JEM and they can fix it :P

Lol, I have arranged for my neighbor to bring his HJ ute and trailer there as well in-case I do blow something so he can tow me home :D

Thanks Tez. I have PM'd "Shell" regarding the membership application.

Fingers crossed for this event! Will surely be in-line for the July one :)

Are you wanting to go onto the reserve list Raj?

Membership form filled out?

You've got a good chance now!

Regards Terry

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...