Jump to content
SAU Community

Recommended Posts

Yep I see what you mean R33 TB wise . The Neo plenums mount flange doesn't have the extra material to cover the back of the barbs hole like the R33s plenum does .

Thanks but I know someone who I think still has R33 upper and lower manifold halves bare . What I want to do is measure the diameter of the ports where the upper and lower halves of the R33 version bolts together . I measured the Neo Turbo version and the ports are just over 41mm diameter - around 41.2mm . The Neos shim gasket is a very neat fit here .

A . 

  • 3 weeks later...

Hi all , finally got to measure the difference in bore size between R33 RB25DET and R34 RB25DET inlet manifolds where the plenum bolts to the lower legs .

As you'll see its close to 6mm which is considerable . From what I've seen in the past many RB manifolds , except RB26 , seem to be reduced in size or shape in later versions .

Nissan obviously thought higher gas speeds and possibly a lesser plenum chamber volume was way to go on the GTt along with head and piston differences .

The pic with my grubby finger in it is pointing to the water inlet to the Neo's front bleeder , I'm curious to know if the pipe size and hose is the same size as the hose up from the barbed fitting behind the water pump on R33's .

As I've said in the past there's heaps of minor changes all over the Neo 25T and all look to be a step in the right direction .

A .   

20171021_173426.jpg

20171021_173636.jpg

20171021_173752.jpg

20171021_173729.jpg

20171021_174104.jpg

20171021_174145.jpg

20171021_175154.jpg

20171021_173825.jpg

20171021_175218.jpg

20171021_175102.jpg

20171021_175233.jpg

Edited by discopotato03
  • 3 years later...

The most involved part is making up a spacer plate if you want to use the R33's throttlebody and TPS on the Neo 25's manifold . I was given an R33 manifold top section so I cut its TB flange off and machined the rough side flat in a centre lathe . 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...