Jump to content
SAU Community

Recommended Posts

Some days it will drive for hours with no problem. Other times it will shut of 4-5 times in the space of a minute. There is no warning when this happens and you literally do not know 1 second beforehand. There is a very slight engine stumble sometimes but 99% of the time you cannot regain it even if you floor it, it acts like a kill switch. You can shift to neutral and restart the car. It may drive for hours or switch of 1 second after you restart it.

What I have done so far.

Replaced fuel pump and fuel filter with brand new units

Changed spark plugs and checked coils.

Checked some vacuum lines

Cleaned MAF sensor

CHanged Crank angle sensor (its a the black plastic unit from a R34 with the half moon because its a late series 2 aka series 3)

The car is fitted with both an immoboliser and turbo timer. I suspect these may be a culprit. Any common fault I should check before I pull these out?

The car is a late 1998 R33 gts-t.

Link to comment
https://www.sau.com.au/forums/topic/421766-r33-suddenly-shuts-of-while-driving/
Share on other sites

I had a problem like this but it was after i changed my turbo inlet pipe. My MAF was suffering from reversion BIG time cuasing it to spazz out and shut off. I could almost ALWAYS make it shutt off while going up a hill and then pushing in the clutch to let the RPMs drop.

Ok guys after taking out the turbo timer and immoboliser, the problem is still exactly the same, which is a shame because now those units have to go back in and it was all for nothing.

Scotty nm35, The fuel pump is this one http://www.ebay.com.au/itm/Performance-Fuel-Pump-Skyline-RB20-RB25-R32-R33-R34-/120568439688?pt=AU_Car_Parts_Accessories&hash=item1c12706388

The relay used is the same as the stock unit. Only the bracket had to be really modded.

GTR nation, the old fuel pump DID make a whining loud whining noise, the new one does not. Have not monitored fuel pump volatge when this happens. Would need some kind of digital data logger as it may take as long as a day to turn of and you cant keep your eyes glued to the multimeter.

I am going to try a new MAF unit next but its very frustarting. Should have taken firestorms advice but it may end up doing the same thing with a new maf. Guess it was the easiest thing to try first though.

Edited by sonicz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...