Jump to content
SAU Community

Recommended Posts

Hey guys,

Just after some help with my current problem.

When I drive my car and go over 5000rpm the revs hold up. When its in gear it will hold the revs say at 4000rpm and when I engage the clutch it will redline. It does this for a few seconds then goes back to normal.

When this happened last I put my foot behind the pedal and it was all the way up.

I've checked if the throttle cable is jamming and I can't fault it when the car isn't moving.

Cleaned the AAC

Cleaned the throttle body

What else can I check? I'm lost at what it could be.

Mods are:

Greddy plenum

Hypertune throttle body

3037s

Injectors

Power fc

Z32

It had all this work even before the problem started. And sometimes it won't happen

Thanks for your help

Link to comment
https://www.sau.com.au/forums/topic/421902-rb25-problem/
Share on other sites

Possible TPS fault. If you can get a commander hooked up to the ECU, look for TPS voltage to drop to <0.5 V as you close the throttle.

Also you need to look for vacuum leaks and watch the ignition timing. If it is unusually high, that may cause a big rev too.

Thanks mate, ill check the tps

I don't think it would be a vacuum leak because it doesn't happen all the time

Link to comment
https://www.sau.com.au/forums/topic/421902-rb25-problem/#findComment-6787956
Share on other sites

I changed the tps and the problem is still occurring.

I took the throttle body off and it still looks good. Sat there for a while opening and closing it and never jammed.

While I was out testing the problem again I would dab the throttle when it was keeping the revs up and it would stop.

I'm going to have a look at where the throttle cable joins the pedal and see how I go.

Wish me luck

Link to comment
https://www.sau.com.au/forums/topic/421902-rb25-problem/#findComment-6791345
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...