Jump to content
SAU Community

Recommended Posts

1992 Black R32 gts-t.
DRIVELINE:
-Series 2 RB25DET motor and gearbox

-Rebalanced KKR430 turbo
-3" Turbo back exhaust (from cat back is Bee Racing(Bee*R) from Japan)
-Microtech LT-16S ECU w/ MAP sensor
-Splitfire coils
-OSGiken Camgear
-Gates Racing timing belt/tensioners/idler pulley
-Sard fpr

- Walbro 255l/hr fuel pump
-Blitz pod filter
-JustJap 600x300 FMIC
-Exedy Sport tuff clutch (the pink pressure plate ones)
-Gibson motorsport custom 3" single piece tailshaft.
-Tuned by DAT performace (the guy who does the dyno at Powercruise)
-Makes 239kW at only 12psi NO LAG! Have dyno sheets.

SUSPENSION/BRAKES:
-HSD coilovers
-Bee*R pineapple bushes (subframe collars)
-KKR Castor rods
-HICAS lock-bar
-DBA Slotted rotors
-QFM700 pads all-round (outperform redstuff)
-Can provide front strut brace

WHEELS AND TYRES:
-18x10 +18 Work Emotion XD9s
-235/40R18 Federal 595s all round with 90% tread
-Guards rolled and pumped to fit the rims

INTERIOR:
-Red BRIDE Cuga Carbon-fibre Drivers seat
-R33 GT-R Passenger seat
-Deep dish suede wheel with yellow centre marker
-Microtech control unit
-Pioneer head unit with bluetooth handsfree
-Pioneer speakers all round

$9500

Car will be sold with RWC, can register at buyers cost after deposit put down if convenient for buyer.

Contact Jono: 0421 308 872

post-46140-0-64362100-1363682653_thumb.jpgpost-46140-0-61819200-1363682666_thumb.jpgpost-46140-0-72524300-1363682788_thumb.jpgpost-46140-0-44757900-1363682804_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/421954-qld-1992-r32-gtst-with-rb25det/
Share on other sites

I bought the car near stock in 2007 from its first aussie owner 21000km ago, engine and gearbox came from a front cut series 2 R33 with 80000km on the clock and was put in the car just under 5000km ago


I built this car to have real world performance and be drivable and well mannered on the street, things look very stealth under the bonnet and in almost 6 years of ownership the car has never been defected. with some injectors 18-20psi and a small edit to the tune, this car would see 270rwkw+ with no issues.

car will be sold with RWC, can register once deposit taken if preferred (at buyers cost).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...