Jump to content
SAU Community

Intercooler Install - Before and After...

Gizmo73

By Gizmo73,
in Engines & Forced Induction

 Share

Recommended Posts

Gizmo73 Proficient

Gizmo73

Posted
Posted

Hi Guys..

I got my front mount intercooler installed last week, and i am a bit dubious about the dyno reading - in that its too high..

I have had two dyno readings - both done with the same settings on the same dyno in the same place - all in shootout mode.....please keep in mind these dyno runs are done just so i know where i stand with the car - im not after dyno output figures only tuning, as this car's objective is the 1/4 mile...

1st dyno run: 166RWKW (HKS super-dragger exhaust, front dump pipe, HKS air pod) - This is about what i expected, which is fine..

Installed GTR front mount intercooler - 120 bend from plenum, 2.5 aluminium pipes all round, cut front bar, plumb back BOV (turbosmart)

2nd Dyno Run: 196RWKW/199RWKW/203RWKW - wtf ?? On the sheet, the first run (done about a month ago) was overlayed, and the difference is all mid range/top end. Additionally, the a/f ratio leaned out a tad, which is also what i expected..

However, i wouldnt expect more than about 10RWKW with this mod, due to the decreased resistence in boost.

Boost is stock, as is the turbo - i was paranoid and all the way home checked the boost gauge (stock) to see if something was amiss to count for the extra power - didnt go over 3.5.. (7psi...ish)

The car as since done about 200kms, so im pretty sure everything that has to be connected is. The feel is that the car is most improved top end about 5,000rpm...

Im after any plausible explanations for this - i dont care about the figures, moreso the huge jump.

Thanks,

Matt

Link to comment
https://www.sau.com.au/forums/topic/42301-intercooler-install-before-and-after/
Share on other sites
Sciby Experienced

Sciby

Posted
Posted

Perhaps the dyno is a little bit overzealous... my car with full zorst and air pod managed 149.2rwkw on a cold day with a tank of Ultimate, in shootout... car was tiptop, no other issues... and a @40rwkw gain from an FMIC sounds huge...

Either the dyno is out, or there's something in your car that you don't know about. :D

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi Matt, this is a mixture of comments and questions....

A standard R33 GTST puts out 120-125 rwkw on our dyno, we have had about 20 of them now and that's about the average (and applies to over 80% of the time). With RAWS compliancing we are seeing more and more stock standard cars.

Your car had

just a HKS super-dragger exhaust, front dump pipe, HKS air pod
and made 166 rwkw (ie; 41-46 rwkw more). Based on my experiences, I don't think so! :headspin:

More like 146 rwkw I would say.

Then

GTR front mount intercooler - 120 bend from plenum, 2.5 aluminium pipes all round, cut front bar, plumb back BOV
makes another 37 rwkw (up to 203 rwkw).

The best I have seen out of that upgrade is 25 rwkw accompanied by a small increase in boost, about 1-2 psi. So when you say stock boost? Where is that measured? On what gauge?

Final comment is, I have yet to see an R33 RB25DET make 200 + rwkw without some form of A/F ratio correction (SAFC or PFC etc) and a boost increase, with 10 to 12 psi being the normal level. For your upgrade level I would expect 170 to 175 rwkw. The A/F ratio correction usually yields around 10 to 15 rwkw and the boost increase a similar 10 to 15 rwkw increase. Thus 200 rwkw is a common goal with a standard turbo whilst maintaining some life. :freak:

It would help a great deal if you could post the dyno graphs, there are generally a lot of clues contained therein. :aroused:

Hope that all makes some sense

Guest Robo's

Guest Robo's

Posted
Posted
Interesting... generally the anecdotal evidence is the other way around, bigger gains for gears than the FMIC... weird. :D

Its quite common knowledge that the exhaust cam gear on a R33 yields about 5rwkw. Going by the seat of the pants feel, thats as most as i got too. With the FMIC, i could feel a noticeable gain.

Guest Robo's

Guest Robo's

Posted
Posted
Well, if it's common knowledge, there's a lot of people out there who have it wrong.

Well i have been reading these forums for about a year now and its quite common knowledge. Maybe your getting mixed up with the GTR in which they get around 20rwkw with both inlet and exhaust cam gears adjustments.

Gizmo73 Proficient

Gizmo73

Posted
  • Author
Posted

Hey Guys - thanks for the interesting posts.....

Hi Sciby - im sure the dyno is reading high - im more interested in the RWKW difference (which is about 40RWKW) than the actual figure. im using this diagnosis as a tuning tool, nothing more - as i wish to get this beast out on the 1/4 mile to prove its worth..

Generally - no cam gears (yet - soon, though) - and running stock boost (7psi) and stock turbo

Hi Knore - hard to say in regards to SOTP feel. Im sure it feels better, but its hard to say 40RWKW better. Im sure this mod would pickup boost increase by default (due to less restriction), however this should be about .5-1 psi i wouldve thought...

Hey SydneyKid - stock boost is as it states - i havent touched the turbo or boost in any way, shape or form on this car. The boost is measured on the stock gauge for the moment (bad, i know) - and this is based on the fact that at 5k RPM the boost gauge is not going much past 3.0...this tells me that as inaccurate as the gauge is, the car is not running over 10psi (being generous)...ill try and scan the dyno sheet...

Hey Nathan....it was a dyno dynamics dyno, in shootout mode - same settings for both runs..

Cheers,

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      You're retired Mark, on bin night, go for a walk, kind of like you're doing the beep test. Put one rock in the first neighbours, come back, get another rock, go to the second neighbours, repeat over many weeks. All rocks eventually gone...
    • The Bogan
      NC MX5

      By The Bogan · Posted

      No chop chop of anything mate, it is what it is, plus, I don't want any air that isn't either going through the cooling stack or intake getting into the engine compartment increasing under bonnet pressure  Yeah, the Mazda Speed aftermarket intake above is less than ideal for multiple reasons, the requirement to remove the bumper every time you need to service the filter, and also smaller in diameter than the NC1 OEM one Weirdly, Mazda Speed is part of the Mazda motorsport division, "form over function" and $$$$$ for Mazda from unsuspecting punters I suspect  After some googling about them it seems they added no power, but do increase some induction noise Meh In other news, the electricians have been busy today at the house, and are back tomorrow finishing up all the security stuff and exterior lighting, they also added some lighting on the garage ceiling, which will come in handy when working in the garage when it's not freezing out there My Birdies raised garden bed also arrived today as well, which I'll put together and place tomorrow, it's a big tall Bessie, 74cm high, 92cm wide and 214cm long, this will come in handy as I am starting to get "stockpiles" of good soils from doing landscaping, some of the clean rock, namely the river stone, will go into the bottom of the bed for drainage, as well as the old Apricot tree that was out the back,  and when it's full, I'll grab another one, I will be growing enough veggies to keep me both busy as well as supplementing the shopping list I'm also awaiting another quote for a new Colourbond front fence, as the "1980 style cemented in rock edging" that was there and "fashionable at the time" looked arse, and my god, the amount of cement used to fix the rock was insane, it took 1.5 days for me to break out 12 meters of the stuff by hand, trim the bushes back to the fence line and dump it out the back of the joint to deal with at a later date,I will soon need a skip bin to tip it all Unfortunately they did alot of the cemented in rock around the joint, which I hate, so a few pallets of retaining wall blocks for around the front and back where the cemented in rock is will be required to bring it up to a standard, and look, that I will be happy with 12 meters worth of rock and cement Finished smashing the fence line and ready for a fence to be installed, yes, the lawns need some TLC and thickness, the previous owner trimmed the grass to the roots 😢, the TLC I can provide, and nature over time will do the rest And there's probably about another 40 meters worth of this landscaping abomination left to do around the front and back gardens, I'm guessing maybe 3 or 4 tons worth, tip fees for this will be a killer Meh, all in all I'm having fun and keeping busy, plus, it's good PT
    • Murray_Calavera
      Ethanol Content Sensor - Always at 11%?

      By Murray_Calavera · Posted

      If I drove to a typical petrol station, what would my choices of fuel be? 
    • MBS206
      NC MX5

      By MBS206 · Posted

      Just cut the bottom of the guard out. It's no longer got a big duct, to a sealed box, or a restriction. It has all the cold air from outside. Also, that cai you showed looks terrible. Bends are NOT good for go gos!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
×
×
  • Create New...